ST72334J datasheet(108/125 Pages) STMICROELECTRONICS

108 / 125 page

ST72334J/N, ST72314J/N, ST72124J

108/125

8.5 I/O PORT CHARACTERISTICS

Recommended operating conditions

with TA=-40 to +85

oC and 4.5V<V

DD-VSS<5.5V unless otherwise specified.

Notes:

1) Unless otherwise specified, typical data are based on TA=25°C and VDD-VSS=5V. They are given only as design guide-

lines and are not tested.

2) Data based on design simulation and/or technology characteristics, not tested in production.

3) Hysteresis voltage between Schmitt trigger switching levels. Based on characterization results, not tested.

4) Data based on characterization results, not tested in production.

5) Positive injection (IINJ+)

The IINJ+ is performed through protection diodes insulated from the substrate of the die.

The true open-drain pins do not accept positive injection. In this case the maximum voltage rating must be respected.

6) ADC accuracy reduced by negative injection (IINJ- )

The IINJ- is performed through protection diodes NOT INSULATED from the substrate of the die. The drawback is a small

leakage (a few

µA) induced inside the die when a negative injection is performed. This leakage is tolerated by the digital

structure, but it acts on the analog line depending on the impedance versus a leakage current of a few

µA (if the MCU

has an AD converter). The effect depends on the pin which is submitted to the injection. Of course, external digital signals

applied to the component must have a maximum impedance close to 50K

Ω.

Location of the negative current injection:

- Pins with analog input capability are the most sensitive. IINJ- maximum is 0.8 mA (assuming that the impedance of the

analog voltage is lower than 25K

Ω)

- Pure digital pins can tolerate 1.6mA. In addition, the best choice is to inject the current as far as possible from the analog

input pins.

7) When several inputs are submitted to a current injection, the maximum IINJ is the sum of the positive (or negative) cur-

rents (instantaneous values). These results are based on characterisation with IINJ maximum current injection on four I/

O port pins of the device.

8) To generate an external interrupt, a minimum pulse width has to be applied on an I/O port pin configured as an external

interrupt source.

I/O PORT PINS

Symbol

Parameter

Conditions

Min

Typ 1)

Max

Unit

VIL

Input low level voltage 2)

3V<VDD-VSS<5.5V

0.3xVDD

VIH

Input high level voltage 2)

0.7xVDD

VHYS

Schmitt trigger voltage hysteresis 3)

400

VOL

Output low level voltage

for Standard I/O port pins

I=-5mA

1.3

I=-2mA

0.5

Output low level voltage

for high sink I/O port pins

I=-20mA

1.3

I=-8mA

0.5

VOH

Output high level voltage

I=-5mA

VDD-2.0

I=-2mA

VDD-0.8

RPU

Pull-up equivalent resistor

VIN >VIH

VIN <VIL

100

140

Ω

Input leakage current

VSS<VPIN<VDD

µA

ISV

Static current consumption 2)

Floating input mode

200

IPINJ

Single pin injected current

Positive 5):VEXT>VDD

Negative 6):VEXT<VSS

-5

IINJ

Total injected current 7)

(sum of all I/O and control pins)

Positive: VEXT>VDD

tbd

Negative: VEXT<VSS

tbd

tOHL

Output high to low level fall time

Cl=50pF

14.8 4)

45.6 4)

tOLH

Output low to high rise time

14.4 4)

45.9 4)

tITEXT

External interrupt pulse time 8)

1tCPU

ST72334J Datasheet(PDF) 108 Page - STMicroelectronics

ST72334J Datasheet(HTML) 108 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL