PIC16F685-ESLASHMLQTP datasheet(130/294 Pages) MICROCHIP

130 / 294 page

PIC16F631/677/685/687/689/690

DS41262D-page 128

11.1

Capture Mode

In Capture mode, CCPR1H:CCPR1L captures the

16-bit value of the TMR1 register when an event occurs

on pin CCP1. An event is defined as one of the

following and is configured by the CCP1M<3:0> bits of

the CCP1CON register:

• Every falling edge

• Every rising edge

• Every 4th rising edge

• Every 16th rising edge

When a capture is made, the Interrupt Request Flag bit

CCP1IF of the PIR1 register is set. The interrupt flag

must be cleared in software. If another capture occurs

before the value in the CCPR1H, CCPR1L register pair

is read, the old captured value is overwritten by the new

captured value (see Figure 11-1).

11.1.1

CCP1 PIN CONFIGURATION

In Capture mode, the CCP1 pin should be configured

as an input by setting the associated TRIS control bit.

FIGURE 11-1:

CAPTURE MODE

OPERATION BLOCK

DIAGRAM

11.1.2

TIMER1 MODE SELECTION

Timer1 must be running in Timer mode or Synchronized

Counter mode for the CCP module to use the capture

feature. In Asynchronous Counter mode, the capture

operation may not work.

11.1.3

SOFTWARE INTERRUPT

When the Capture mode is changed, a false capture

interrupt may be generated. The user should keep the

CCP1IE interrupt enable bit of the PIE1 register clear to

avoid false interrupts. Additionally, the user should

clear the CCP1IF interrupt flag bit of the PIR1 register

following any change in operating mode.

11.1.4

CCP PRESCALER

There are four prescaler settings specified by the

CCP1M<3:0>

bits

the

CCP1CON

Whenever the CCP module is turned off, or the CCP

module is not in Capture mode, the prescaler counter

is cleared. Any Reset will clear the prescaler counter.

Switching from one capture prescaler to another does not

clear the prescaler and may generate a false interrupt. To

avoid this unexpected operation, turn the module off by

clearing the CCP1CON register before changing the

prescaler (see Example 11-1).

EXAMPLE 11-1:

CHANGING BETWEEN

CAPTURE PRESCALERS

Note:

If the CCP1 pin is configured as an output,

a write to the port can cause a capture

condition.

CCPR1H

CCPR1L

TMR1H

TMR1L

Set Flag bit CCP1IF

(PIR1 register)

Capture

Enable

CCP1CON<3:0>

Prescaler

÷ 1, 4, 16

and

Edge Detect

CCP1

System Clock (FOSC)

BANKSEL CCP1CON

;Set Bank bits to point

;to CCP1CON

CLRF

CCP1CON

;Turn CCP module off

MOVLW

NEW_CAPT_PS ;Load the W reg with

; the new prescaler

; move value and CCP ON

MOVWF

CCP1CON

;Load CCP1CON with this

; value

PIC16F685-E/MLQTP Datasheet(PDF) 130 Page - Microchip Technology

PIC16F685-E/MLQTP Datasheet(HTML) 130 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL