PIC16F1824-ESLASHML datasheet(151/420 Pages) MICROCHIP

151 / 420 page

 2010 Microchip Technology Inc.

Preliminary

DS41419A-page 151

PIC16F/LF1824/1828

15.2

ADC Operation

15.2.1

STARTING A CONVERSION

To enable the ADC module, the ADON bit of the

ADCON0 register must be set to a ‘1’. Setting the GO/

DONE bit of the ADCON0 register to a ‘1’ will start the

Analog-to-Digital conversion.

15.2.2

COMPLETION OF A CONVERSION

When the conversion is complete, the ADC module will:

• Clear the GO/DONE bit

• Set the ADIF Interrupt Flag bit

• Update the ADRESH and ADRESL registers with

new conversion result

15.2.3

TERMINATING A CONVERSION

If a conversion must be terminated before completion,

the GO/DONE bit can be cleared in software. The

ADRESH and ADRESL registers will be updated with

the partially complete Analog-to-Digital conversion

sample. Incomplete bits will match the last bit

converted.

15.2.4

ADC OPERATION DURING SLEEP

The ADC module can operate during Sleep. This

requires the ADC clock source to be set to the FRC

option. When the FRC clock source is selected, the

ADC waits one additional instruction before starting the

conversion. This allows the SLEEP instruction to be

executed, which can reduce system noise during the

conversion. If the ADC interrupt is enabled, the device

will wake-up from Sleep when the conversion

completes. If the ADC interrupt is disabled, the ADC

module is turned off after the conversion completes,

although the ADON bit remains set.

When the ADC clock source is something other than

FRC, a SLEEP instruction causes the present conver-

sion to be aborted and the ADC module is turned off,

although the ADON bit remains set.

15.2.5

SPECIAL EVENT TRIGGER

The Special Event Trigger of the CCPx/ECCPX module

allows periodic ADC measurements without software

intervention. When this trigger occurs, the GO/DONE

bit is set by hardware and the Timer1 counter resets to

zero.

Using the Special Event Trigger does not assure proper

ADC timing. It is the user’s responsibility to ensure that

the ADC timing requirements are met.

Refer to Section 23.0 “Capture/Compare/PWM

Modules” for more information.

Note:

The GO/DONE bit should not be set in the

same instruction that turns on the ADC.

Refer to Section 15.2.6 “A/D Conver-

sion Procedure”.

Note:

A device Reset forces all registers to their

Reset state. Thus, the ADC module is

turned off and any pending conversion is

terminated.

TABLE 15-2:

SPECIAL EVENT TRIGGER

Device

CCPx/ECCPx

PIC16F/LF1824/1828

CCP4

PIC16F1824-E/ML Datasheet(PDF) 151 Page - Microchip Technology

PIC16F1824-E/ML Datasheet(HTML) 151 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL