MCP1710 datasheet(4/24 Pages) MICROCHIP

4 / 24 page

MCP1710

DS20005158D-page 4

 2012-2015 Microchip Technology Inc.

Load Regulation

VOUT/VOUT

—1

%VIN =(VIN(Min) +VIN(Max))/2,

IOUT = 0.02 mA to 200 mA

(Note 1)

Dropout Voltage

VDROPOUT

——

450

IOUT =200 mA,

VR ≤ 3.5V (Note 3)

——

400

IOUT = 100 mA,

VR > 3.5V (Note 3)

Shutdown Input

Logic High Input

VSHDN-HIGH

——

%VIN VIN =VIN(Min) to 5.5V (Note 1)

Logic Low Input

VSHDN-LOW

——

%VIN VIN =VIN(Min) to 5.5V (Note 1)

AC Performance

Output Delay From SHDN

TOR

—

SHDN = GND to VIN,

VOUT = GND to 95% VR

Output Noise

—0.37

—

µV/

Hz IOUT =50mA, f= 1kHz,

COUT = 2.2 µF (X7R Ceramic),

VR =2.5V

Power Supply Ripple

Rejection Ratio

PSRR

—

f = 100 Hz, IOUT =10 mA,

VINAC =200 mV pk-pk,

CIN =0 µF

TEMPERATURE SPECIFICATIONS

Electrical Specifications: Unless otherwise noted, VIN =VR +800 mV, (Note 1), IOUT =1 mA, CIN =COUT =2.2 µF

(X7R Ceramic), TA =+25°C. Boldface type applies for junction temperatures, TJ of -40°C to +85°C (Note 4)

Parameters

Sym.

Min.

Typ.

Max.

Units

Conditions

Temperature Ranges

Operating Junction

Temperature Range

-40

—

+85

°C

Steady state

Maximum Junction

Temperature

——

+150

°C

Transient

Storage Temperature Range

-65

—

+150

°C

Thermal Package Resistances

Thermal Resistance,

2x 2 VDFN-8

JA

—73.1—

°C/W

JEDEC® standard FR4 board with

1 oz copper and thermal vias

JC

—10.7—

°C/W

AC/DC CHARACTERISTICS (CONTINUED)

Electrical Specifications: Unless otherwise noted, VIN =VR +800 mV (Note 1), IOUT =1 mA, CIN =COUT =2.2 µF

(X7R Ceramic), TA =+25°C. Boldface type applies for junction temperatures TJ of -40°C to +85°C (Note 4).

Parameters

Sym.

Min.

Typ.

Max.

Units

Conditions

Note 1:

The minimum VIN must meet two conditions: VIN  VIN(Min) and VIN  VR  VDROPOUT(Max).

VR is the nominal regulator output voltage. VR = 1.2V, 2.5V, etc.

Dropout voltage is defined as the input-to-output voltage differential at which the output voltage drops 3%

below its nominal value that was measured with an input voltage of VIN =VOUT(Max) +VDROPOUT(Max).

The junction temperature is approximated by soaking the device under test at an ambient temperature

equal to the desired junction temperature. The test time is small enough such that the rise in the junction

temperature over the ambient temperature is not significant.

MCP1710 Datasheet(PDF) 4 Page - Microchip Technology

MCP1710 Datasheet(HTML) 4 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

Datasheet Download

Link URL