HIP1013 datasheet(4/7 Pages) RENESAS

4 / 7 page

HIP1013

FN4516 Rev 3.00

Page 4 of 7

August 2004

Absolute Maximum Ratings TA = 25°C

Thermal Information

VDD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-0.3V to +17V

3/12VG, CPUMP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 25V

3/12VISEN, 3/12VS . . . . . . . . . . . . . . . . . . . . . . . -5V to VDD + 0.3V

5VISEN, 5VS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -5V to 7.5V

PGOOD, RILIM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 7.5V

MODE/PWRON1, PWRON2, 5VG . . . . . . . . . .-0.3V to VDD + 0.3V

ESD Classification . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2kV (Class 2)

Operating Conditions

VDD Supply Voltage Range . . . . . . . . . . . . . . . . . . . +10.5V to +16V

Temperature Range (TA). . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C

Thermal Resistance (Typical, Note 1)

JA (°C/W)

SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

120

Maximum Junction Temperature (Plastic Package) . . . . . . . . 150°C

Maximum Storage Temperature Range . . . . . . . . . . -65°C to 150°C

Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . . 300°C

(SOIC - Lead Tips Only)

CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the

device at these or any other conditions above those indicated in the operational sections of this specification is not implied.

NOTES:

JA is measured with the component mounted on an evaluation PC board in free air.

2. All voltages are relative to GND, unless otherwise specified.

Electrical Specifications

VDD = 12V, CVG = 0.01F, RSENSE = 0.1, CBULK = 220F, ESR = 0.5, TA = TJ = 0°C to 70°C, Unless

Otherwise Specified

PARAMETER

SYMBOL

TEST CONDITIONS

MIN

TYP

MAX

UNITS

CONTROL SECTION

Current Limit Threshold Voltage

(Voltage Across Sense Resistor)

VIL

RILIM = 10k

100

115

Over Current Limit Response Time

OCLrt

Current Overload, RILIM = 10k, RSHORT = 6.0

-2

s

Response Time To Dead Short

RTSHORT CVG = 0.01F

500

1000

12V Gate Turn-On Time

tON12V

CVG = 0.01F-

5V Gate Turn-On Time

tON5V

CVG = 0.01F-

Gate Turn-On Current

ION

CVG = 0.01F

A

12V Under Voltage Threshold

12VVUV

10.5

10.8

11.0

5V Under Voltage Threshold

5VVUV

4.35

4.5

4.65

3.3V Under Voltage Threshold

3.3VVUV

2.65

2.8

2.95

Charge pumped 12VG Voltage

V12VG

CPUMP = 0.1F

16.8

17.3

17.9

3/5VG High Voltage

3/5VG

11.2

11.9

SUPPLY CURRENT AND IO SPECIFICATIONS

VDD Supply Current

IVDD

VDD POR Rising Threshold

PORrvth

9.5

10.0

10.5

VDD POR Falling Threshold

PORfvth

9.3

9.8

10.3

PWRON Pull-up Voltage

PWRN_V

PWRON pins open

1.8

2.4

3.2

PWRON Rising Threshold

PWR_Vth

1.1

1.5

PWRON Hysteresis

PWR_hys

0.1

0.2

0.3

PWRON Pull-Up Current

PWRN_I

100

A

RILIM Pin Current Source Output

RILIM_Io

100

110

A

Charge Pump Output Current

Qpmp_Io

CPUMP = 0.1F, CPUMP = 16V

400

590

800

A

Charge Pump Output Voltage

Qpmp_Vo

No load

17.2

17.4

Charge Pump Output Voltage - Loaded

Qpmp_VIo Load current = 100

A

16.2

16.7

Charge Pump POR Rising Threshold

Qpmp+Vth

15.6

16.5

Charge Pump POR Falling Threshold

Qpmp-Vth

15.2

15.7

16.2

HIP1013 Datasheet(PDF) 4 Page - Renesas Technology Corp

HIP1013 Datasheet(HTML) 4 Page - Renesas Technology Corp

Html Pages

1 2 3 4 5 6 7

Datasheet Download

Link URL