PN 4096896

September 2011

2011 Fluke Corporation. All rights reserved. Printed in U.S.A.

All product names are trademarks of their respective companies.

How to Prime the Test Pump

Before you connect the Pump to the Unit Under Test (UUT), the

Pump must be filled with fluid and primed for use. Follow the

directions below to prepare the Pump for use.

1. Fill the Pump with fluid:

a. Remove the Reservoir Filler Cap (item

.)

b. Fill the Hydraulic Fluid Reservoir approximately two-thirds full

(66 cc) with distilled water, mineral oil, or hydraulic oil.

Note

If water is used in the Pump, use only DISTILLED water

and drain the water out of the Pump after use.

c.

Install the Reservoir Filler Cap (item

.) Tighten by hand.

2. Prime the Pump:

a. Adjust the Vernier Fine Adjustment Knob (item

) to the

approximate middle-range.

b. Turn the Pressure Bleed Knob (item

) clockwise until it

stops in the full closed position.

c. Squeeze the handles together to pump fluid. Pump fluid until

fluid shows at the Pump Port.

d. Attach the fluid hose to the Pump.

e. Squeeze the handles together until fluid shows at the end of

the hose.

f.

Attach the fluid hose to the Unit Under Test (UUT) and

squeeze the Pump handles until pressure increases.

g. Bleed the trapped air from the Pump. Pressurize the Pump to

1,000 psi then slowly turn the Pressure Bleed Knob (item

)

counter-clockwise to release pressure.

Notes

• As the pressure rises it will be hard to squeeze the

handles together. Use the Handle Limiter (item

limit the travel of the handles which will make them

easier to squeeze together. To toggle the Handle

Limiter on or off, squeeze the handles together and

push the Handle Limiter (item

• The rate at which the pressure increases is directly

related to the test configuration (hose length and

volume of UUT.)

Replacement Parts

Rebuild Kit, Fluke PN 4097836

Hydraulic Fluid Reservoir Rebuild Kit, Fluke PN 2844341

Handle Assembly Rebuild Kit, Fluke PN 2844352

LIMITED WARRANTY AND LIMITATION OF LIABILITY

This Fluke product will be free from defects in material and workmanship for

one year from the date of purchase. This warranty does not cover fuses,

disposable batteries, or damage from accident, neglect, misuse, alteration,

contamination, or abnormal conditions of operation or handling. Resellers are

not authorized to extend any other warranty on Fluke’s behalf. To obtain

service during the warranty period, contact your nearest Fluke authorized

service center to obtain return authorization information, then send the product

to that Service Center with a description of the problem.

THIS WARRANTY IS YOUR ONLY REMEDY. NO OTHER WARRANTIES,

SUCH AS FITNESS FOR A PARTICULAR PURPOSE, ARE EXPRESSED OR

IMPLIED. FLUKE IS NOT LIABLE FOR ANY SPECIAL, INDIRECT,

INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOSSES, ARISING

FROM ANY CAUSE OR THEORY. Since some states or countries do not

allow the exclusion or limitation of an implied warranty or of incidental or

consequential damages, this limitation of liability may not apply to you.

Fluke Corporation

P.O. Box 9090

Everett, WA 98206-9090

U.S.A.

Fluke Europe B.V.

P.O. Box 1186

5602 BD Eindhoven

The Netherlands

11/99

Fluke-700HTP-2

Hydraulic Test Pump

Instruction Sheet

Introduction

The Fluke 700HTP-2 Hydraulic Test Pump (the Pump or Product) is a

portable source of high pressure.

Safety

W Warning

To prevent personal injury, use the Product only as

specified, or the protection supplied by the Product can be

compromised.

Pump Specifications

• Maximum pressure: 10,000 psi (690 bar)

• Hydraulic media: distilled water, mineral based hydraulic oil, or up

to hydraulic oil 100 (30 W).

• Wetted materials: 303 stainless steel, aluminum, polyurethane,

PTFE, nitrile, and nylon.

• Weight: 1.29 lb (0.58 kg)

• Dimensions: length 9.5 in (241 mm), width 6.1 in (155 mm), depth

2.6 in (66 mm)

Box Contents

• Model 700HTP-2 Hydraulic Test Pump with a 1/4-inch NPT tee

installed.

• Two 1/4-inch NPT male to 1/4-inch BSP female adapters.

• One 1/4-inch NPT male to 1/4-inch NPT male fitting.

• One 1/4-inch NPT male to 1/8-inch NPT male fitting.

• Instruction Sheet

How to Contact Fluke

To contact Fluke, call one of the following telephone numbers:

• Technical Support USA: 1-800-44-FLUKE

(1-800-443-5853)

• Calibration/Repair USA: 1-888-99-FLUKE

(1-888-993-5853)

• Canada: 1-800-36-FLUKE

(1-800-363-5853)

• Europe: +31 402-675-200

• Japan: +81-3-6714-3114

• Singapore: +65-738-5655

• Anywhere in the world: +1-425-446-5500

Or, visit Fluke's website at www.fluke.com.

To register your product, visit http://register.fluke.com.

To view, print, or download the latest manual supplement, visit

http://us.fluke.com/usen/support/manuals.