AM29LV065DU101REF datasheet(26/54 Pages) AMD

26 / 54 page

Am29LV065D

February 16, 2006

vice to normal operation. Table 10 shows the address

and data requirements for both command sequences.

See also “SecSi (Secured Silicon) Sector Flash

Memory Region” for further information.

Byte Program Command Sequence

Programming is a four-bus-cycle operation. The pro-

gram command sequence is initiated by writing two

unlock write cycles, followed by the program set-up

command. The program address and data are written

next, which in turn initiate the Embedded Program al-

gorithm. The system is not required to provide further

controls or timings. The device automatically provides

internally generated program pulses and verifies the

programmed cell margin. Table 10 shows the address

and data requirements for the byte program command

sequence.

When the Embedded Program algorithm is complete,

the device then returns to the read mode and ad-

dresses are no longer latched. The system can deter-

mine the status of the program operation by using

DQ7, DQ6, or RY/BY#. Refer to the Write Operation

Status section for information on these status bits.

Any commands written to the device during the Em-

bedded Program Algorithm are ignored. The SecSi

sector, autoselect, and CFI functions are not available

when a program function is in progress. Note that a

hardware reset immediately terminates the program

operation. The program command sequence should

be reinitiated once the device has returned to the read

mode, to ensure data integrity.

Programming is allowed in any sequence and across

sector boundaries. A bit cannot be programmed

from “0” back to a “1.” Attempting to do so may

cause the device to set DQ5 = 1, or cause the DQ7

and DQ6 status bits to indicate the operation was suc-

cessful. However, a succeeding read will show that the

data is still “0.” Only erase operations can convert a “0”

to a “1.”

Unlock Bypass Command Sequence

The unlock bypass feature allows the system to pro-

gram bytes to the device faster than using the stan-

dard program command sequence. The unlock bypass

command sequence is initiated by first writing two un-

lock cycles. This is followed by a third write cycle con-

taining the unlock bypass command, 20h. The device

then enters the unlock bypass mode. A two-cycle un-

lock bypass program command sequence is all that is

required to program in this mode. The first cycle in this

sequence contains the unlock bypass program com-

mand, A0h; the second cycle contains the program

address and data. Additional data is programmed in

the same manner. This mode dispenses with the initial

two unlock cycles required in the standard program

command sequence, resulting in faster total program-

ming time. Table 10 shows the requirements for the

command sequence.

During the unlock bypass mode, only the Unlock By-

pass Program and Unlock Bypass Reset commands

are valid. To exit the unlock bypass mode, the system

must issue the two-cycle unlock bypass reset com-

mand sequence. The first cycle must contain the data

90h. The second cycle must contain the data 00h. The

device then returns to the read mode.

The device offers accelerated program operations

through the ACC pin. When the system asserts V

HH on

the ACC pin, the device automatically enters the Un-

lock Bypass mode. The system may then write the

two-cycle Unlock Bypass program command se-

quence. The device uses the higher voltage on the

ACC pin to accelerate the operation. Note that the

ACC pin must not be at V

HH for operations other than

accelerated programming, or device damage may re-

sult.

Figure 4 illustrates the algorithm for the program oper-

ation. Refer to the Erase and Program Operations

table in the AC Characteristics section for parameters,

and Figure 16 for timing diagrams.

Figure 4.

Program Operation

START

Write Program

Command Sequence

Data Poll

from System

Verify Data?

Yes

Last Address?

Yes

Programming

Completed

Increment Address

Embedded

Program

algorithm

in progress

Note: See Table 10 for program command sequence.

AM29LV065DU101REF Datasheet(PDF) 26 Page - Advanced Micro Devices

AM29LV065DU101REF Datasheet(HTML) 26 Page - Advanced Micro Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54

Datasheet Download

Link URL