EVAL-AD7764EBZ datasheet(21/32 Pages) AD

21 / 32 page

AD7764

Rev. 0 | Page 21 of 32

AD7764 FUNCTIONALITY

SYNCHRONIZATION

The SYNC input to the AD7764 provides a synchronization

function that allows the user to begin gathering samples of the

analog front-end input from a known point in time.

The SYNC function allows multiple AD7764s, operated from

the same master clock, that use common SYNC and RESET

signals to be synchronized so that each ADC simultaneously

updates its output register.

Connect common MCLK, SYNC and RESET signals to all

AD7764 devices in the system. On the falling edge of the SYNC

signal, the digital filter sequencer is reset to 0. The filter is held

in a reset state until a rising edge of the SCO senses SYNC high.

Thus, to perform a synchronization of devices, a SYNC pulse of

a minimum of 2.5 ICLK cycles in length can be applied,

synchronous to the falling edge of SCO. On the first rising edge

of SCO after SYNC goes logic high, the filter is taken out of reset,

and the multiple parts gather input samples synchronously.

Following a SYNC, the digital filter needs time to settle before

valid data can be read from the AD7764. The user knows there

is valid data on the SDO line by checking the FILTER-SETTLE

status bit (see D7 in Table 9) that is output with each conversion

result. The time from the rising edge of SYNC until the FILTER-

SETTLE bit asserts depends on the filter configuration used. See

the Theory of Operation section and the values listed in Table 6

for details on calculating the time until FILTER-SETTLE

asserts. Note that the FILTER_SETTLE bit is designed as a

reactionary flag to indicate when the conversion data output

is valid.

OVERRANGE ALERTS

The AD7764 offers an overrange function in both a pin and

status bit output. The overrange alerts indicate when the voltage

applied to the AD7764 modulator input pins exceeds the limit

set in the overrange register, indicating that the voltage applied

is approaching a level where the modulator will be overranged.

To set this limit, the user must program the register. The default

overrange limit is set to 80% of the VREF voltage (see the

AD7764 Registers section).

The OVERRANGE pin outputs logic high to alert the user

that the modulator has sampled an input voltage greater in

magnitude than the overrange limit as set in the overrange

modulator samples an input above the overrange limit. Once

the input returns below the limit, the OVERRANGE pin returns

to zero. The OVERRANGE pin is updated after the first FIR

filter stage. Its output changes at the ICLK/4 frequency.

The OVR status bit is output as Bit D6 on SDO during a data

conversion, and can be checked in the AD7764 status register.

This bit is less dynamic than the OVERRANGE pin output. It is

updated on each conversion result output, that is, the bit

changes at the output data rate. If the modulator has sampled a

voltage input that exceeded the overrange limit during the

process of gathering samples for a particular conversion result

output, then the OVR bit is set to logic high.

LOGIC

LEVEL

LOGIC

LEVEL

OUTPUT FREQUENCY

OF FIR FILTER 1 = ICLK/4

OVERRANGE

LIMIT

OVERRANGE

LIMIT

OBSOLUTE INPUT

TO AD7764

[(VIN+) – (VIN–)]

OUTPUT DATA RATE (ODR)

(ICLK/DECIMATION RATE

Figure 38. OVERRANGE Pin and OVR Bit vs. Absolute Voltage

Applied to Modulator

The output points from FIR Filter 1 in Figure 38 are not drawn

to scale relative to the output data rate points. The FIR Filter 1

output is updated either 16×, 32×, or 64× faster than the output

data rate depending on the decimation rate in operation.

POWER MODES

During power-up, the AD7764 defaults to operate in normal

power mode. There is no register write required.

The AD7764 also offers low power mode. To operate the device

in low power mode, the user sets the LPWR bit in the control

low power mode has no impact on the output data rate or

available bandwidth.

SCO (O)

CONTROL REGISTER

ADDRESS 0x0001

LOW POWER MODE

DATA 0x0010

FSI (I)

SDI (I)

32 ×

tSCO

Figure 39. Write Scheme for Low Power Mode

The AD7764 features a RESET/PWRDWN pin. Holding the

input to this pin logic low places the AD7764 in power-down

mode. All internal circuitry is reset. To utilize the RESET

functionality, pulse the input to this pin low for a minimum of

one MCLK period. This action resets the internal circuitry.

When the AD7764 receives a logic high input on the RESET/

PWRDWN pin, the device powers up.

EVAL-AD7764EBZ Datasheet(PDF) 21 Page - Analog Devices

EVAL-AD7764EBZ Datasheet(HTML) 21 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32

Datasheet Download

Link URL