GaAs SP6T Switch, Absorptive, Single Supply

DC - 4.0 GHz

SW90-0004A

M/A-COM Inc. and its affiliates reserve the right to make changes to the

product(s) or information contained herein without notice. M/A-COM makes

no warranty, representation or guarantee regarding the suitability of its

products for any particular purpose, nor does M/A-COM assume any liability

whatsoever arising out of the use or application of any product(s) or

information.

• North America Tel: 800.366.2266 / Fax: 978.366.2266

• Europe Tel: 44.1908.574.200 / Fax: 44.1908.574.300

• Asia/Pacific Tel: 81.44.844.8296 / Fax: 81.44.844.8298

Visit www.macom.com for additional data sheets and product information.

V7

2

Parameter

Test Conditions

Frequency

Units

Min.

Typ.

Max.

Insertion Loss

RFC-RF1, 2, 3, 4, 5, 6

DC - 3.0 GHz

3.0 - 4.0 GHz

dB

dB

—

—

—

—

2.1

2.4

Isolation

—

DC - 4.0 GHz

dB

25

—

—

VSWR

On (RFC, RF1-RF6)

Logic per Truth Table

Off (RF1-RF6)

Logic per Truth Table

DC - 4.0 GHz

DC - 4.0 GHz

Ratio

Ratio

—

—

—

—

2.0:1

2.0:1

1 dB Compression

—

—

50 MHz

0.5 - 4.0 GHz

dBm

dBm

—

—

15

27

—

—

Two-tone inputs up to +5 dBm

50 MHz

0.5-4.0 GHz

dBm

dBm

—

—

30

40

—

—

Switching Speed

Ton (50% Control to 10% RF)

nS

—

20

—

Toff (50% Control to 90% RF)

nS

—

15

—

Trise (10% to 90% RF)

nS

—

5

—

Tfall (90% to 10% RF)

nS

—

2

—

Vcc

—

—

V

4.5

5.0

5.5

Logic “0”

Sink Current is 20 A max.

—

V

0.0

—

0.8

Logic “1”

Source Current is 20 A max.

—

V

2.0

—

5.0

Icc

7

Vcc min to max, Logic “0” or “1”

—

mA

—

5

8

Switching Noise

Generated from

DC-DC Converter with

recommended capacitors

3.5 MHz

dBm

—

-93

—

Turn-on Current

8

For guaranteed start-up

—

mA

—

—

125

Thermal Resistance θjc

—

—

°C/W

—

15

—

7. During turn-on, the device requires an initial start up current (Icc) specified as “Turn-on Current”. Once operational, Icc will drop to the

specified levels. This is not applicable to dual supply operation.

8. The DC-DC converter is guaranteed to start in 100 s as long as the power supplies have the maximum turn-on current available for

start-up.

Control Inputs

Condition of Switch

"0" is TTL Low, "1" is TTL High

C1

C2

C3

C4

C5

C6

RF1

RF2

RF3

RF4

RF5

RF6

1

0

0

0

0

0

On

Off

Off

Off

Off

Off

0

1

0

0

0

0

Off

On

Off

Off

Off

Off

0

0

1

0

0

0

Off

Off

On

Off

Off

Off

0

0

0

1

0

0

Off

Off

Off

On

Off

Off

0

0

0

0

1

0

Off

Off

Off

Off

On

Off

0

0

0

0

0

1

Off

Off

Off

Off

Off

On

RF Common to Each RF Port

Truth Table