TLC2201CD datasheet(15/66 Pages) TI

15 / 66 page

TLC220x, TLC220xA, TLC220xB, TLC220xY

Advanced LinCMOS

™ LOW-NOISE PRECISION

OPERATIONAL AMPLIFIERS

SLOS175 – FEBRUARY 1997

POST OFFICE BOX 655303

• DALLAS, TEXAS 75265

TLC2202C electrical characteristics at specified free-air temperature, VDD± = ±5 V (unless

otherwise noted)

PARAMETER

TEST CONDITIONS

TA†

TLC2202AC

TLC2202BC

UNIT

PARAMETER

TEST CONDITIONS

TA†

MIN

TYP

MAX

MIN

TYP

MAX

UNIT

VIO

Input offset voltage

°C

500

µV

VIO

In ut offset voltage

Full range

650

µV

αVIO

Temperature coefficient

VIC =0

RS =50 Ω

Full range

µV/°C

αVIO

of input offset voltage

VIC = 0,

RS = 50 Ω

Full range

0.5

µV/°C

Input offset voltage long-term

drift (see Note 4)

°C

0.001

0.005

0.001

0.005

µV/mo

IIO

Input offset current

°C

0.5

IIO

In ut offset current

VIC =0

RS =50 Ω

Full range

100

IIB

Input bias current

VIC = 0,

RS = 50 Ω

°C

IIB

In ut bias current

Full range

100

Common mode input voltage

–5

VICR

Common-mode input voltage

range

RS = 50 Ω

Full range

range

2.7

VOM

Maximum positive peak

°C

4.7

4.8

4.7

4.8

VOM +

output voltage swing

RL =10kΩ

Full range

4.7

VOM

Maximum negative peak

RL = 10 kΩ

°C

– 4.7

– 4.9

– 4.7

– 4.9

VOM –

output voltage swing

Full range

– 4.7

VO = ± 4V

RL = 500 kΩ

°C

300

560

300

560

AVD

Large-signal differential

VO = ± 4 V,

RL = 500 kΩ

Full range

200

V/mV

AVD

voltage amplification

VO = ± 4V

RL =10kΩ

°C

100

V/mV

VO = ± 4 V,

RL = 10 kΩ

Full range

CMRR

Common-mode rejection ratio

VIC = VICRmin,

°C

115

CMRR

Common-mode rejection ratio

ICR

VO = 0,

RS = 50 Ω

Full range

kSVR

Supply-voltage rejection ratio

VDD

± = ±2 3Vto ±8V

°C

110

kSVR

(

∆VDD±/∆VIO)

VDD

± = ±2.3 V to ±8 V

Full range

IDD

Supply current

VO =0

No load

°C

1.8

2.7

1.8

2.7

IDD

ly current

VO = 0,

No load

Full range

2.7

† Full range is 0

°C to 70°C.

NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at TA = 150°C extrapolated

to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.

TLC2202C operating characteristics at specified free-air temperature, VDD± = ±5 V

PARAMETER

TEST CONDITIONS

TA†

TLC2202AC

TLC2202BC

UNIT

PARAMETER

TEST CONDITIONS

TA†

MIN

TYP

MAX

MIN

TYP

MAX

UNIT

±23 V

°C

Slew rate at unity gain

VO = ± 2.3 V,

°C

1.8

2.7

1.8

2.7

µs

Slew rate at unity gain

RL = 10 kΩ,CL = 100 pF

Full range

1.3

µs

Equivalent input noise voltage

f = 10 Hz

°C

nV/

√Hz

(see Note 5)

f = 1 kHz

°C

nV/

√Hz

VN(PP)

Peak-to-peak equivalent input

f = 0.1 to 1 Hz

°C

0.5

µV

VN(PP)

noise voltage

f = 0.1 to 10 Hz

°C

0.7

µV

Equivalent input noise current

°C

0.6

fA/

√Hz

f=10kHz

RL =10kΩ

Gain-bandwidth product

f = 10 kHz,

RL = 10 kΩ,

CL 100 pF

°C

1.9

MHz

CL = 100 pF

φm

Phase margin at unity gain

RL =10kΩ CL = 100 pF

°C

φm

Phase margin at unity gain

RL = 10 kΩ, CL = 100 F

°C

† Full range is 0

°C to 70°C.

NOTE 5: This parameter is tested on a sample basis for the TLC2202A and on all devices for the TLC2202B. For other test requirements, please

contact the factory. This statement has no bearing on testing or nontesting of other parameters.

TLC2201CD Datasheet(PDF) 15 Page - Texas Instruments

TLC2201CD Datasheet(HTML) 15 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66

Datasheet Download

Link URL