ALUMINUM ELECTROLYTIC CAPACITORS

Tangent of loss angle (tan δ)

(Terminal dimensions)

(PC board hole dimensions)

L

1

A

2

Q

3

2

4

D

5

6

6

8

7

1

8

M

9

E

10

L

11

A

12

4

13

0

14

15 16

Configuration

Case dia. code

Case length code

Bottom Plate

Rated capacitance (680µF)

Rated voltage (200V)

Series name

Type

φD

22

25

30

35

Code

Z

A

B

C

ZB

code less

With Bottom

Plate

Without

Bottom Plate

Capacitance tolerance (±20%)

Polarity bar

（10

）

L±2

4.0±0.5

Pressure relief vent

Bottom plate

(code ZB only)

Sleeve (PET)

Please contact to us if other configurations are required.

10

±0.1

2

×φ2±0.1

1.5

0.8

+0.2

-0.1

+0.2

-0.1

0.8 +0.2

-0.1

Within ±20% of the initial capacitance value

Within ±15% of the initial capacitance value

Drawing

Type numbering system (Example : 200V 680µF)

LAQSnap-inTerminalType, 105°CPermissibleAbnormalVoltage,

Smaller-sized

Withstanding 2000 hours application of rated ripple current of 105°C.

Extended voltage range at 200V, 220V and 400V.

Smaller case sizes and higher ripple current than LAK.

Improved safety features for abnormally excessive voltage.

Ideally suited for the equipment used at voltage fluctuating area.

Compliant to the RoHS directive (2011/65/EU,(EU)2015/863).

Specifications

Category Temperature Range

Rated Voltage Range

Rated Capacitance Range

Capacitance Tolerance

Leakage Current

Stability at Low Temperature

Endurance

Shelf Life

Safety Performance

Marking

Performance Characteristics

Item

–

25 to +105°C

200 • 220 • 400V

33 to 1500µF

± 20% at 120Hz, 20°C

0.20max. 120Hz at 20°C

Printed with white color letter on black sleeve

The specifications listed at right shall be met when the

capacitors are restored to 20°C after D.C. bias plus rated

ripple current is applied for 2000 hours at 105°C, the

peak voltage shall not exceed the rated voltage.

After storing the capacitors under no load at 105°C for 1000

hours and then performing voltage treatment based

on JIS C 5101-4 clause 4.1 at 20°C,

they shall meet the requirements listed at right.

The pressure relief vent will operate in normal conditions, with no dangerous conditions such as flames, ignitions or dispersion of pieces of the capacitor and / or case.

Rating

Voltage (V)

200

Rated Capacitance (µF)

330

C < 330

330

C < 470

470

C < 470

Limited DC current

Test voltage

4 A

5 A

7 A

300VDC and 375VDC

Test conditions

LAQ

Smaller

I

(µA) (After 5 minutes' application of rated voltage at 20°C) [C : Rated Capacitance (µF) V : Voltage (V)]

Rated voltage (V)

Impedance ratio (max.)

Z(– 25°C) / Z(+20°C)

200 • 220 • 400

8

220

330

C < 330

330

C < 470

470

C < 470

4 A

5 A

7 A

320VDC and 405VDC

400

330

C < 100

100

C < 220

220

C < 470

2 A

4 A

7 A

500VDC and 600VDC

Capacitance change

Leakage current

tan δ

Less than or equal to the initial specified value

200% or less than the initial specified value

Capacitance change

Leakage current

tan δ

Less than or equal to the initial specified value

150% or less than the initial specified value

3 CV

3 CV

3 CV

Dimension table in next page.

LAK

Measurement frequency : 120Hz

CAT.8100N