ALUMINUM ELECTROLYTIC CAPACITORS

Shelf Life

Tangent of loss angle (tan δ)

LAR Snap-inTerminalType,105°CPermissibleOvervoltage

Withstanding 2000 hours application of rated ripple current

at 105°C.

Reduction of short incidence when overvoltage (rated

voltage x 1.5) is applied to a capacitor.

Compliant to the RoHS directive (2011/65/EU,(EU)2015/863).

Specifications

Category Temperature Range

Rated Voltage Range

Rated Capacitance Range

Capacitance Tolerance

Leakage Current

Stability at Low Temperature

Endurance

Marking

Performance Characteristics

Item

– 40 to +105˚C (200 250V), – 25 to +105˚C (400 450V)

200 to 450V

82 to 2200µF

± 20% at 120Hz, 20˚C

Printed with white color letter on black sleeve.

When overvoltage (rated voltage x 1.5, limited current = 1A) is applied to a capacitor, more than 60% of the capacitors are passing.

(passing condition : The pressure relief vent will operate normally or will not be opened for 10min without short and flame.)

Safety Performance

The specifications listed at right shall be met when the

capacitors are restored to 20°C after D.C. bias plus

rated ripple current is applied for 2000 hours at 105°C,

the peak voltage shall not exceed the rated voltage.

Measurement frequency : 120Hz at 20˚C

Leakage current

tan δ

Capacitance change

Less than or equal to the initial specified value

200% or less than the initial specified value

Within ±20% of the initial capacitance value

Dimension table in next page.

LAR

LGU

Permissible

Overvoltage

(µA) (After 5 minutes' application of rated voltage at 20°C

) [C : Rated Capacitance(µF), V : Voltage ( V ) ]

3

I

CV

Rated voltage (V)

200 to 400

450

tan δ (max.)

0.15

0.20

Measurement frequency : 120Hz

Rated voltage(V)

Impedance ratio

(max.)

200 • 250

400 • 450

3

12

8

-----

Z(–25°C) / Z(+20°C)

Z(–40°C) / Z(+20°C)

10

±0.1

2

×φ2±0.1

(Terminal dimensions)

(PC board hole dimensions)

1.5

0.8

+0.2

-0.1

+0.

2

-0.1

0.8

+0.2

-0.1

L

1

A

2

R

3

2

4

G

5

1

6

2

7

1

8

M

9

E

10

L

11

Z

12

3

13

0

14

Configuration

Case dia. code

Case length code

Rated Capacitance (120F)

Rated voltage (400V)

Series name

Type

φD

22

25

30

35

Code

Z

A

B

C

Capacitance tolerance (20%)

Polarity bar

(10)

L±2

 4.0±0.5

Pressure relief vent

Sleeve (PET)

100.

1

2-2φ±0.1

(Terminal dimensions)

(PC board hole dimensions)

1.5

0.8

+0.2

-0.1

+0.2

-0.1

0.8

+0.2

-0.1

L

1

A

2

R

3

2

4

G

5

1

6

2

7

1

8

M

9

E

10

L

11

Z

12

3

13

0

14

Configuration

Case dia. code

Case length code

Rated capacitance (120µF)

Rated voltage (400V)

Series name

Type

φD

22

25

30

35

Code

Z

A

B

C

Capacitance tolerance (±20%)

Polarity bar

10

L2

4.00.5

Pressure relief vent

Sleeve (P.E.T.)

Drawing

Type numbering system (Example : 400V 120µF)

200,250V

400,450V

50

0.81

0.77

60

0.85

0.82

120

1.00

1.00

300

1.17

1.16

1k

1.32

1.30

10k

1.45

1.41

50k or more

1.50

1.43

Frequency coefficient of rated ripple current

Capacitance change

tan δ

Leakage current

Within ±15% of the initial capacitance value

150% or less than the initial specified value

Less than or equal to the initial specified value

After storing the capacitors under no load at 105°C for 1000

hours and then performing voltage treatment based

on JIS C 5101-4 clause 4.1 at 20°C,

they shall meet the requirements listed at right.

The other terminal is also available upon request.

Please refer

to page

"Snap-in Terminal type Terminal-Shape"

for schematic of dimensions.

Frequency(Hz)

coeff.

CAT.8100N