ALUMINUM ELECTROLYTIC CAPACITORS

CAT.8100M

LGG Snap-inTerminalType,105°CUltra-Smaller-Sized

Type numbering system (Example : 400V 180µF)

Drawing

L

1

G

2

G

3

2

4

G

5

1

6

8

7

1

8

M

9 10

E

13

L

11

14

A

12

2 5

Configuration

Case dia. code

Case length code

Capacitance tolerance (±20%)

Rated capacitance (180µF)

Rated voltage (400V)

Series name

Type

φD

22

25

30

Code

Z

A

B

35

C

10±

0.1

2-2φ± 0.1

(Terminal dimensions)

The other terminal is also available upon request.

Please refer page 272 for schematic of dimensions.

(PC board hole dimensions)

1.5

0.8

+0.2

-0.1

+0.2

-0.1

0.8+0.2

-0.1

Polarity bar

10

L± 2

4.0± 0.5

Pressure relief vent

Sleeve (P.E.T.)

L

1

G

2

G

3

2

4

G

5

1

6

8

7

1

8

M

9 10

E

13

L

11

14

A

12

2 5

Configuration

Case dia. code

Case length code

Capacitance tolerance (±20%)

Rated capacitance (180µF)

Rated voltage (400V)

Series name

Type

φD

22

25

30

Code

Z

A

B

35

C

10

±0.1

2

×φ2±0.1

(Terminal dimensions)

(PC board hole dimensions)

1.5

0.8

+0.2

-0.1

+0.2

-0.1

0.8+0.2

-0.1

Polarity bar

(10

)

L±2

4.0±0.5

Pressure relief vent

Sleeve (PET)

One rank smaller case sized than LGN.

Suited for equipment down sizing.

Compliant to the RoHS directive (2011/65/EU,(EU)2015/863).

Smaller

LGG

LGN

Smaller

LGL

Item

Marking

160 to 250

4

Specifications

Category Temperature Range

Rated Voltage Range

Rated Capacitance Range

Capacitance Tolerance

Leakage Current

Tangent of loss angle (tan δ)

Stability at Low Temperature

Endurance

Shelf Life

Performance Characteristics

–

40 to +105°C (160 to 250V) , – 25 to +105°C (400 to 450V)

160 to 450V

100 to 3300µF

± 20% at 120Hz, 20°C

Printed with white color letter on black sleeve.

Measurement frequency : 120Hz

Temperature : 20°C

Z(– 25°C) / Z(+20°C)

Rated voltage (V)

Impedance ratio

(max.)

400 to 450

8

I

(µA) (After 5 minutes' application of rated voltage at 20°C) [C : Rated Capacitance (µF) V : Voltage (V)]

3 CV

3 CV

3 CV

The specifications listed at right shall be met when the

capacitors are restored to 20°C after D.C. bias plus

rated ripple current is applied for 2000 hours at 105°C,

the peak voltage shall not exceed the rated voltage.

After storing the capacitors under no load at 105°C for 1000

hours and then performing voltage treatment based

on JIS C 5101-4 clause 4.1 at 20°C,

they shall meet the characteristic requirements listed at right.

Measurement frequency : 120Hz at 20°C

Rated voltage (V)

tan δ (max.)

160 to 420

0.15

450

0.20

Less than or equal to the initial specified value

Within ± 20% of the initial capacitance value

Leakage current

Capacitance change

tan δ

200% or less than the initial specified value

Less than or equal to the initial specified value

Within ± 20% of the initial capacitance value

Leakage current

Capacitance change

tan δ

200% or less than the initial specified value

Dimension table in next page.

Other terminations available upon request.

Please refer to the Guidelines for Aluminum Electrolytic Capacitors.