 |
Electronic Components Datasheet Search |
|
|
Electronic Components Datasheet Search |
|
TUSB2E2211005VBWR Datasheet(PDF) 48 Page - Texas Instruments |
|
|
|||||||||||||||||||||||||||||
TUSB2E2211005VBWR Datasheet(HTML) 48 Page - Texas Instruments |
|
|
48 / 63 page  Return to the Summary Table. Table 9-26. GLOBAL_CONFIG Register Field Descriptions Bit Field Type Reset Description 7 SOFT_RST WtoPH 0h Writing a 1 to this field is equivalent to pulsing RESETB low 6 DISABLE_P1 R/W 0h Disabled Mode Repeater 1 (I2C remains Active) (If port is not disconnected, wait until disconnect event to disable the repeater) 0h = Repeater Enabled 1h = Repeater Disabled 5 DISABLE_P0 R/W 0h Disabled Mode Repeater 0 (I2C remains Active) (If port is not disconnected, wait until disconnect event to disable the repeater) 0h = Repeater Enabled 1h = Repeater Disabled 4 INT_OUT_TYPE R/W 0h INT Output Type INT output drive strength in open-drain mode is the same as GPIO setting 0h = Open Drain 1h = push pull 3 INT_POLARITY R/W 0h INT pin polarity in push-pull mode only (open-drain mode is always Active low) 0h = Active High (only for push-pull) 1h = Active Low (only for push-pull, open-drain is always active low) 2 RESERVED R/W 0h Reserved 1-0 RESERVED R 0h Reserved 9.1.25 INT_ENABLE_1 Register (Offset = B3h) [Reset = 00h] INT_ENABLE_1 is shown in Table 9-27. Return to the Summary Table. Table 9-27. INT_ENABLE_1 Register Field Descriptions Bit Field Type Reset Description 7 GPIO1_RISING_EDGE R/W 0h INT_GPIO1_RISING_EDGE enable. When GPIO1_IN_TRIGGER_TYPE = 0 (Edge), this enables interrupt on Rising Edge of GPIO1. When GPIO1_IN_TRIGGER_TYPE = 1 (Level), this enables Interrupt when GPIO1 = High. 0h = Not Enabled 1h = Enabled 6 GPIO1_FALLING_EDGE R/W 0h INT_GPIO1_FALLING_EDGE enable. When GPIO1_IN_TRIGGER_TYPE = 0 (Edge), this enables interrupt on Falling Edge of GPIO1. When GPIO1_IN_TRIGGER_TYPE = 1 (Level), this enables Interrupt when GPIO1 = Low. 0h = Not Enabled 1h = Enabled 5 GPIO0_RISING_EDGE R/W 0h INT_GPIO0_RISING_EDGE enable. When GPIO0_IN_TRIGGER_TYPE = 0 (Edge), this enables interrupt on Rising Edge of GPIO0. When GPIO0_IN_TRIGGER_TYPE = 1 (Level), this enables Interrupt when GPIO0 = High. 0h = Not Enabled 1h = Enabled TUSB2E221 SNLS757D – JUNE 2024 – REVISED OCTOBER 2025 www.ti.com 48 Submit Document Feedback Copyright © 2025 Texas Instruments Incorporated Product Folder Links: TUSB2E221 |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
English ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
