MOSEL VITELIC

MSM9026

6/6

PID342 10/96

Taiwan

#1, Creation Road I,

Science - based Industrial Park,

Hsinchu, 30077

Taiwan, ROC

"audio_reply@ccmail.mosel.com.tw"

TEL: 886-3-5770055

FAX: 886-3-5772788

FAX: 886-3-5784732

Taipei

7F, #102 Sec. 3,

Ming Chung E. Road,

Taipei,105

Taiwan, ROC

TEL: 886-2-5451213

FAX: 886-2-5451214

Hongkong

#19 Dai

Fu Street,

Taipo Industrial Estate,

Taipo, N.T.

Hongkong

TEL: 852-2388-8277(MKO)

TEL: 852-2665-4883

FAX: 852-2664-2406

FAX: 852-2770-8011(MKO)

U.S.A.

#3910 North First Street,

San Jose,

CA. 65134-1501

U.S.A.

TEL: 1-408-433-6000

FAX: 1-408-433-0952

Before Operating 9026

To prepare voice file(s)

To prepare up to 32 voice files by MES 2.0 or 3.0.

These files must be 8-bit PCM file.

To prepare a filled PRF

To write down your demand options on PRF (product

request form) is strongly recommended before you

are running 9026pack.exe.

To prepare a source text

Using commercial text editor on personal computer,

you can set up a source text in the format defined in

9026pack software user's manual (pid 392 10/96). In

this source text, you can define the both word

sections and sentence tables. This source text must

have the file extension .SRC. Most of mask options

can be defined on the screen in 9026pack.exe. The

entry dependent options could be defined inside

source text.

To have a compiled binary file

Running 9026pack.exe and entering keystrokes as

prompt, you can easily define the options and read in

the source text. Completing as the screen tells, you

can get a compiled binary file in your specified file

name. Its file extension is always .BIN.

To have 27C010 programmed

Programming this .BIN file into an 27C010 chip by

commercial EPROM programmer, you have it ready.

To insert this 27C010

To insert this EPROM chip into textool U3 of 9026

board in right direction.

To set up LED selections

To set up LED connection by jumper 3x5 if needed.

To set up Trigger Drive

To set up trigger drive circuit as your requirement on

jumper 3x6. Without the drive source (either high or

low, either R or bare wire) the switch keeps floating

and never be capable to activate the trigger. Without

right polarity of drive source you can neither trigger

the sound and you may hurt this 9026 board.

To configure demanded wires

Ensuring you have both 1.5Vx4 power and speaker

well connected, this board are ready to work. There

are push-button switches to turn on or off the power.

Red LED lamp D3 tells the power on. JP2 enables the

auto power off function.

Operation Flow

Warning

Output pin definition restricted: If you select LED

dynamic flash, then the M9026 output level will remain

the same as the output level of the previous entry.

Trigger pin definition restricted: M9026 performs

two trigger options only, active high & pull low & low

latch as well as active low & pull high & high latch.

The M9026 debounce time (min. trigger pulse width) is

shown as table in page 3/6, not optional as chip.

Misc

Fuse : Not Available

Power : 1.5V x 4 (battery) or 6 VDC power supply

Dimension : (LxWxH) 160x115x20 mm

textool included

Weight : 150 g

Demonstration Kit

filled Product Request Form

Run 9026PACK.EXE

Get Output file filename.BIN

and file filename.OPT

Go EPROM programmer

Get 27C010 programmed

Insert onto 9026 board

Source Text .SRC

Voice files