74LVC2G66

All information provided in this document is subject to legal disclaimers.

© NXP Semiconductors N.V. 2016. All rights reserved.

Product data sheet

Rev. 9 — 15 December 2016

5 of 26

NXP Semiconductors

74LVC2G66

Bilateral switch

9.

Recommended operating conditions

[1]

To avoid sinking GND current from terminal nZ when switch current flows in terminal nY, the voltage drop across the bidirectional switch

must not exceed 0.4 V. If the switch current flows into terminal nZ, no GND current will flow from terminal nY. In this case, there is no

limit for the voltage drop across the switch.

[2]

For overvoltage tolerant switch voltage capability, refer to 74LVCV2G66.

[3]

Applies to control signal levels.

10. Static characteristics

Table 6.

Operating conditions

Symbol

Parameter

Conditions

Min

Max

Unit

VCC

supply voltage

1.65

5.5

V

VI

input voltage

0

5.5

V

VSW

switch voltage

[1][2]

0VCC

V

Tamb

ambient temperature

40

+125

C

t/V

input transition rise and fall rate

VCC =1.65Vto2.7V

[3]

-

20

ns/V

VCC = 2.7 V to 5.5 V

[3]

-

10

ns/V

Table 7.

Static characteristics

At recommended operating conditions; voltages are referenced to GND (ground = 0 V).

Symbol Parameter

Conditions

40 C to +85 C

40 C to +125 C

Unit

Min

Typ[1]

Max

Min

Max

VIH

HIGH-level

input voltage

VCC = 1.65 V to 1.95 V

0.65

 V

CC

-

-

0.65

 V

CC

-V

VCC = 2.3 V to 2.7 V

1.7

-

-

1.7

-

V

VCC = 2.7 V to 3.6 V

2.0

-

-

2.0

-

V

VCC = 4.5 V to 5.5 V

0.7

 V

CC

-

-

0.7

 V

CC

-V

VIL

LOW-level

input voltage

VCC = 1.65 V to 1.95 V

-

-

0.35

 V

CC

-

0.35

 V

CC

V

VCC = 2.3 V to 2.7 V

-

-

0.7

-

0.7

V

VCC = 2.7 V to 3.6 V

-

-

0.8

-

0.8

V

VCC = 4.5 V to 5.5 V

-

-

0.3

 V

CC

-0.3

 V

CC

V

II

input leakage

current

pin nE; VI = 5.5 V or GND;

VCC = 0 V to 5.5 V

[2]

-

0.1

1-

1

A

IS(OFF)

OFF-state

leakage

current

VCC = 5.5 V; see Figure 8

[2]

-

0.1

0.2

-

0.5

A

IS(ON)

ON-state

leakage

current

VCC = 5.5 V; see Figure 9

[2]

-

0.1

1-

2

A

ICC

supply current

VI = 5.5 V or GND;

VSW =GND or VCC;

VCC =1.65Vto 5.5V

[2]

-0.1

4

-

4

A

I

CC

additional

supply current

pin nE; VI =VCC  0.6 V;

VSW =GND or VCC;

VCC =5.5 V

[2]

-

5

500

-

500

A