Notes:

on the side of the unit

Model

Number

Input

Output

Efficiency

(%, Typ)

Fuse Rating

Slow-Blow

(mA)

Voltage (VDC)

Current (mA)

Voltage

(VDC)

Current

(mA, Max)

Current

(mA, Min)

Nominal

Range

Full-Load

No-Load

D101ER

5

4.75 - 5.25

294

30

5.0

200.0

20.0

68

500

D102ER

5

4.75 - 5.25

286

30

9.0

111.0

12.0

70

500

D103ER

5

4.75 - 5.25

282

30

12.0

83.0

9.0

71

500

D104ER

5

4.75 - 5.25

278

30

15.0

67.0

7.0

72

500

D105ER

5

4.75 - 5.25

290

30

±5.0

±100.0

±10.0

69

500

D106ER

5

4.75 - 5.25

286

30

±9.0

±56.0

±6.0

70

500

D107ER

5

4.75 - 5.25

278

30

±12.0

±42.0

±5.0

72

500

D108ER

5

4.75 - 5.25

278

30

±15.0

±33.0

±4.0

72

500

D111ER

12

11.4 - 12.6

121

15

5.0

150.0

15.0

69

200

D112ER

12

11.4 - 12.6

117

15

9.0

111.0

12.0

71

200

D113ER

12

11.4 - 12.6

116

15

12.0

83.0

9.0

72

200

D114ER

12

11.4 - 12.6

116

15

15.0

67.0

7.0

72

200

D115ER

12

11.4 - 12.6

119

15

±5.0

±100.0

±10.0

70

200

D116ER

12

11.4 - 12.6

116

15

±9.0

±56.0

±6.0

72

200

D117ER

12

11.4 - 12.6

114

15

±12.0

±42.0

±5.0

73

200

D118ER

12

11.4 - 12.6

114

15

±15.0

±33.0

±4.0

73

200

D121ER

24

22.8 - 25.2

59

8

5.0

150.0

15.0

70

100

D122ER

24

22.8 - 25.2

58

8

9.0

111.0

12.0

72

100

D123ER

24

22.8 - 25.2

57

8

12.0

83.0

9.0

73

100

D124ER

24

22.8 - 25.2

57

8

15.0

67.0

7.0

73

100

D125ER

24

22.8 - 25.2

58

8

±5.0

±100.0

±10.0

72

100

D126ER

24

22.8 - 25.2

58

8

±9.0

±56.0

±6.0

72

100

D127ER

24

22.8 - 25.2

57

8

±12.0

±42.0

±5.0

73

100

D128ER

24

22.8 - 25.2

57

8

±15.0

±33.0

±4.0

73

100

Pin

Single

Dual

1

+Vin

+Vin

2

-Vin

-Vin

4

-Vout

No Pin

6

+Vout

No Pin

7

No Pin

+Vout

9

No Pin

-Vout

10

No Pin Common

Derating Curve

Notes:

1. Output load regulation is specified for a load change of 10% to 100%.

2. These units should not be operated with a load under 10% of full load.

Operation at no-load may cause damage to the unit.

3. These converters will operate without external components. However, when

measuring output ripple, it is recommended that an external ceramic capaci-

tor be placed from the +Vout pin to the -Vout pin for single output units

and from each output to common for dual output units. An input capacitor

will enhace stability

over temperature and

input line variations.

Recommended capaci-

tor values are given in

the table at right. For

applications requir-

ing very low output

noise levels, a simple

LC filter should be effective.

4. It is recommended that a fuse be used on the input of a power supply for

protection. See the Model Selection table above for the correct rating.

Vin

Input

Capacitor

Vout

Output Capacitor

Single

Dual

5 VDC

4.7 μF

5 VDC

10.0 μF

4.7 μF

12 VDC

2.2 μF

9 VDC

4.7 μF

2.2 μF

24 VDC

1.0 μF

12 VDC

2.2 μF

1.0 μF

15 VDC

1.0 μF

0.47 μF

Model Selection Guide

Pin

Connections

Notes:

on the sid

MicroPower Direct

www.micropowerdirect.com

•

FAX: (781) 344-8481

•

E-Mail: sales@micropowerdirect.com