LTC2222 datasheet(5/28 Pages) LINER

5 / 28 page

LTC2222/LTC2223

22223fa

LTC2222

LTC2223

SYMBOL

PARAMETER

CONDITIONS

MIN

TYP

MAX

MIN

TYP

MAX

UNITS

VDD

Analog Supply Voltage

(Note 7)

●

3.1

3.3

3.5

3.1

3.3

3.5

OVDD

Output Supply Voltage

(Note 7)

●

0.5

3.3

3.6

0.5

3.3

3.6

IVDD

Analog Supply Current

●

144

162

111

123

PDISS

Power Dissipation

●

475

535

366

406

PSHDN

Shutdown Power

SHDN = H, OE = H, No CLK

PNAP

Nap Mode Power

SHDN = H, OE = L, No CLK

LTC2222

LTC2223

SYMBOL

PARAMETER

CONDITIONS

MIN

TYP

MAX

MIN

TYP

MAX

UNITS

Sampling Frequency

●

105

MHz

ENC Low Time

Duty Cycle Stabilizer Off

●

4.5

4.76

500

5.9

6.25

500

Duty Cycle Stabilizer On

●

4.76

500

6.25

500

ENC High Time

Duty Cycle Stabilizer Off

●

4.5

4.76

500

5.9

6.25

500

Duty Cycle Stabilizer On

●

4.76

500

6.25

500

tAP

Sample-and-Hold Aperture Delay

ENC to DATA Delay

(Note 7)

●

1.3

2.1

1.3

2.1

ENC to CLOCKOUT Delay

(Note 7)

●

1.3

2.1

1.3

2.1

DATA to CLOCKOUT Skew

(tC - tD) (Note 7)

●

–0.6

0.6

–0.6

0.6

tOE

Output Enable Delay

(Note 7)

●

510

Pipeline Latency

Cycles

POWER REQUIRE E TS The ● denotes the specifications which apply over the full operating temperature

range, otherwise specifications are at TA = 25°C. (Note 8)

TI I G CHARACTERISTICS The ● denotes the specifications which apply over the full operating temperature

range, otherwise specifications are at TA = 25°C. (Note 4)

Note 1: Stresses beyond those listed under Absolute Maximum Ratings

may cause permanent damage to the device. Exposure to any Absolute

Maximum Rating condition for extended periods may affect device

reliability and lifetime.

Note 2: All voltage values are with respect to ground with GND and OGND

wired together (unless otherwise noted).

Note 3: When these pin voltages are taken below GND or above VDD, they will

be clamped by internal diodes. This product can handle input currents of

greater than 100mA below GND or above VDD without latchup.

Note 4: VDD = 3.3V, fSAMPLE = 105MHz (LTC2222) or 80MHz (LTC2223),

differential ENC+/ENC– = 2VP-P sine wave, input range = 2VP-P with differential

drive, unless otherwise noted.

Note 5: Integral nonlinearity is defined as the deviation of a code from a

straight line passing through the actual endpoints of the transfer curve. The

deviation is measured from the center of the quantization band.

Note 6: Offset error is the offset voltage measured from –0.5 LSB when the

output code flickers between 0000 0000 0000 and 1111 1111 1111 in 2’s

complement output mode.

Note 7: Guaranteed by design, not subject to test.

Note 8: VDD = 3.3V, fSAMPLE = 105MHz (LTC2222) or 80MHz (LTC2223),

differential ENC+/ENC– = 2VP-P sine wave, input range = 1VP-P with differential

drive.

LTC2222 Datasheet(PDF) 5 Page - Linear Technology

LTC2222 Datasheet(HTML) 5 Page - Linear Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28

Datasheet Download

Link URL