AD7626

Rev. 0 | Page 8 of 28

PIN CONFIGURATION AND FUNCTION DESCRIPTIONS

VDD1

VDD2

CAP1

REFIN

EN0

EN1

VDD2

CNV–

GND

IN+

IN–

VCM

VDD1

VDD1

VDD2

CLK+

PIN 1

INDICATOR

1

2

3

4

5

6

7

8

24

23

22

21

20

19

18

17

TOP VIEW

(Not to Scale)

AD7626

NOTES

1. CONNECT THE EXPOSED PAD TO THE GROUND

PLANE OF THE PCB USING MULTIPLE VIAS.

Figure 4. Pin Configuration

Table 6. Pin Function Descriptions

Pin No.

Mnemonic

Type1

Description

1

VDD1

P

Analog 5 V Supply. Decouple the 5 V supply with a 100 nF capacitor.

2

VDD2

P

Analog 2.5 V Supply. Decouple this pin with a 100 nF capacitor. The 2.5 V supply source should

supply this pin first, then be traced to the other VDD2 pins (Pin 7 and Pin 18).

3

CAP1

AO

Connect this pin to a 10 nF capacitor.

4

REFIN

AI/O

Prebuffer Reference Voltage. When using the internal reference, this pin outputs the band gap voltage

and is nominally at 1.2 V. It can be overdriven with an external reference voltage such as the ADR280.

In either internal or external reference mode, a 10 μF capacitor is required. If using an external 4.096 V

reference (connected to REF), this pin is a no connect and does not require any capacitor.

5, 6

EN0, EN1

DI

Enable. The logic levels of these pins set the operation of the device as follows:

EN1 = 0, EN0 = 0: power-down mode.

EN1 = 0, EN0 = 1: external 1.2 V reference applied to the REFIN pin is required.

EN1 = 1, EN0 = 0: external 4.096 V reference applied to the REF pin required.

EN1 = 1, EN0 = 1: internal reference and internal reference buffer in use.

7

VDD2

P

Digital 2.5 V Supply. Decouple this pin with a 100 nF capacitor.

8, 9

CNV−, CNV+

DI

Convert Input. These pins act as the conversion control pin. On the rising edge of these pins, the

analog inputs are sampled and a conversion cycle is initiated. CNV+ works as a CMOS input when

CNV− is grounded; otherwise, CNV+ and CNV− are differential LVDS inputs.

10, 11

D−, D+

DO

LVDS Data Outputs. The conversion data is output serially on these pins.

12

VIO

P

Input/Output Interface Supply. Use a 2.5 V supply and decouple this pin with a 100 nF capacitor.

13

GND

P

Ground. Return path for the 100 nF capacitor connected to Pin 12.

14, 15

DCO−, DCO+

DO

LVDS Buffered Clock Outputs. When DCO+ is grounded, the self-clocked interface mode is selected.

In this mode, the 16-bit results on D are preceded by an initial 0 (which is output at the end of the

previous conversion), followed by a 2-bit header (10) to allow synchronization of the data by the

digital host with extra logic. The 1 in this header provides the reference to acquire the subsequent

conversion result correctly. When DCO+ is not grounded, the echoed-clock interface mode is

selected. In this mode, DCO± is a copy of CLK±. The data bits are output on the falling edge of DCO+

and can be captured in the digital host on the next rising edge of DCO+.

16, 17

CLK−, CLK+

DI

LVDS Clock Inputs. This clock shifts out the conversion results on the falling edge of CLK+.

18

VDD2

P

Analog 2.5 V Supply. Decouple this pin with a 100 nF capacitor.

19, 20

VDD1

P

Analog 5 V Supply. Isolate these pins from Pin 1 with a ferrite bead and decouple them with a 100 nF

capacitor.

21

VCM

AO

Common-Mode Output. When using any reference scheme, this pin produces one-half the voltage

present on the REF pin, which can be useful for driving the common mode of the input amplifiers.

22

IN−

AI

Differential Negative Analog Input. Referenced to and must be driven 180° out of phase with IN+.

23

IN+

AI

Differential Positive Analog Input. Referenced to and must be driven 180° out of phase with IN−.