ATmega32A datasheet(110/352 Pages) ATMEL

110 / 352 page

110

8155B–AVR–07/09

ATmega32A

Using the ICR1 Register for defining TOP works well when using fixed TOP values. By using

ICR1, the OCR1A Register is free to be used for generating a PWM output on OC1A. However,

if the base PWM frequency is actively changed by changing the TOP value, using the OCR1A as

TOP is clearly a better choice due to its double buffer feature.

In phase and frequency correct PWM mode, the compare units allow generation of PWM wave-

forms on the OC1x pins. Setting the COM1x1:0 bits to 2 will produce a non-inverted PWM and

an inverted PWM output can be generated by setting the COM1x1:0 to 3 (See Table on page

113). The actual OC1x value will only be visible on the port pin if the data direction for the port

pin is set as output (DDR_OC1x). The PWM waveform is generated by setting (or clearing) the

OC1x Register at the compare match between OCR1x and TCNT1 when the counter incre-

ments, and clearing (or setting) the OC1x Register at compare match between OCR1x and

TCNT1 when the counter decrements. The PWM frequency for the output when using phase

and frequency correct PWM can be calculated by the following equation:

The N variable represents the prescaler divider (1, 8, 64, 256, or 1024).

The extreme values for the OCR1x Register represents special cases when generating a PWM

waveform output in the phase correct PWM mode. If the OCR1x is set equal to BOTTOM the

output will be continuously low and if set equal to TOP the output will be set to high for non-

inverted PWM mode. For inverted PWM the output will have the opposite logic values. If OCR1A

is used to define the TOP value (WGM13:0 = 9) and COM1A1:0 = 1, the OC1A output will toggle

with a 50% duty cycle.

16.9

Timer/Counter Timing Diagrams

The Timer/Counter is a synchronous design and the timer clock (clk

T1) is therefore shown as a

clock enable signal in the following figures. The figures include information on when Interrupt

Flags are set, and when the OCR1x Register is updated with the OCR1x buffer value (only for

modes utilizing double buffering). Figure 16-10 shows a timing diagram for the setting of OCF1x.

Figure 16-10. Timer/Counter Timing Diagram, Setting of OCF1x, No Prescaling

Figure 16-11 shows the same timing data, but with the prescaler enabled.

fOCnxPFCPWM

clk_I/O

NTOP

⋅⋅

----------------------------

clk

(clk

I/O/1)

OCFnx

clk

I/O

OCRnx

TCNTn

OCRnx Value

OCRnx - 1

OCRnx

OCRnx + 1

OCRnx + 2

ATmega32A Datasheet(PDF) 110 Page - ATMEL Corporation

ATmega32A Datasheet(HTML) 110 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL