SN74LVC1G66DBVT datasheet(4/20 Pages) TI

4 / 20 page

www.ti.com

Switching Characteristics

Analog Switch Characteristics

SN74LVC1G66

SINGLE BILATERAL ANALOG SWITCH

SCES323L – JUNE 2001 – REVISED JANUARY 2007

over recommended operating free-air temperature range (unless otherwise noted) (see Figure 5)

VCC = 1.8 V

VCC = 2.5 V

VCC = 3.3 V

VCC = 5 V

FROM

± 0.15 V

± 0.2 V

± 0.3 V

± 0.5 V

PARAMETER

UNIT

(INPUT)

(OUTPUT)

MIN

MAX

MIN

MAX

MIN

MAX

MIN MAX

tpd(1)

A or B

B or A

1.2

0.8

0.6

ten(2)

A or B

2.5

1.9

6.5

1.8

1.5

4.2

tdis(3)

A or B

2.2

1.4

6.9

6.5

1.4

(1)

tPLH and tPHL are the same as tpd. The propagation delay is the calculated RC time constant of the typical on-state resistance of the

switch and the specified load capacitance, when driven by an ideal voltage source (zero output impedance).

(2)

tPZL and tPZH are the same as ten.

(3)

tPLZ and tPHZ are the same as tdis.

A = 25°C

FROM

TEST

PARAMETER

VCC

TYP

UNIT

(INPUT)

(OUTPUT)

CONDITIONS

1.65 V

CL = 50 pF, RL = 600 Ω,

2.3 V

120

fin = sine wave

3 V

175

(see Figure 6)

4.5 V

195

Frequency response(1)

A or B

B or A

MHz

(switch ON)

1.65 V

>300

CL = 5 pF, RL = 50 Ω,

2.3 V

>300

fin = sine wave

3 V

>300

(see Figure 6)

4.5 V

>300

1.65 V

CL = 50 pF, RL = 600 Ω,

2.3 V

Crosstalk

A or B

fin = 1 MHz (square wave)

(control input to signal output)

3 V

(see Figure 7)

4.5 V

100

1.65 V

–58

CL = 50 pF, RL = 600 Ω,

2.3 V

–58

fin = 1 MHz (sine wave)

3 V

–58

(see Figure 8)

4.5 V

–58

Feedthrough attenuation(2)

A or B

B or A

(switch OFF)

1.65 V

–42

CL = 5 pF, RL = 50 Ω,

2.3 V

–42

fin = 1 MHz (sine wave)

3 V

–42

(see Figure 8)

4.5 V

–42

1.65 V

0.1

CL = 50 pF, RL = 10 kΩ,

2.3 V

0.025

fin = 1 kHz (sine wave)

3 V

0.015

(see Figure 9)

4.5 V

0.01

Sine-wave distortion

A or B

B or A

1.65 V

0.15

CL = 50 pF, RL = 10 kΩ,

2.3 V

0.025

fin = 10 kHz (sine wave)

3 V

0.015

(see Figure 9)

4.5 V

0.01

(1)

Adjust fin voltage to obtain 0 dBm at output. Increase fin frequency until dB meter reads –3 dB.

(2)

Adjust fin voltage to obtain 0 dBm at input.

Submit Documentation Feedback

SN74LVC1G66DBVT Datasheet(PDF) 4 Page - Texas Instruments

SN74LVC1G66DBVT Datasheet(HTML) 4 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

Datasheet Download

Link URL