PRF18BE471RB5RB datasheet(96/104 Pages) MURATA

96 / 104 page

!Caution/Notice

(2) Drying

After cleaning, promptly dry this product.

To remove the flux after soldering, observe the following

points in order to avoid deterioration of the characteristics

or any change to the external electrodes' quality.

(1) Cleaning Conditions

2-propanol

Less than 5 minutes

at room temp.

Less than 2 minutes

at 40˚C max.

Less than 1 minute

20W/L Frequency

of several 10kHz

to 100kHz.

Solvent

Dipping Cleaning

Ultrasonic Cleaning

A sufficient cleaning should be applied to remove flux completely.

In your mounting process, observe the following points in

order to avoid deterioration of the characteristics or

destruction of this product. The mounting quality of this

product may also be affected by the mounting conditions,

shown in the points below.

(1) Printing Conditions of Solder Paste

(a) Recommended thickness of solder paste printing

should be from 0.15 to 0.20mm.

(b) After soldering, the solder fillet should be a height

from 0.2 mm to the thickness of this product (see the

figure at right).

stress on this product. Such stress may cause

cracking or other mechanical damage. Also, it can

destroy the electrical performance of this product.

0.2mm

V T V E

Solder

Electrode

1. Solder and Flux

2. Cleaning Conditions and Drying

3. Soldering Conditions

(1) Solder Paste

(a) Flow Soldering: Use Sn:Pb=60:40wt%,

Sn:Pb=63:37wt%, Sn:Ag:Cu=96.5:3.0:0.5wt% or

equivalent type of solder.

(b) Reflow Soldering: Use Sn:Pb=60:40wt%,

Sn:Pb=63:37wt%, Sn:Ag:Cu=96.5:3.0:0.5wt% or

equivalent type of solder paste.

For your reference, we are using "63Sn/37Pb

RMA9086 90-3-M18," manufactured by Alpha Metals

Japan Ltd., "96.5Sn/3.0Ag/0.5Cu

M705-GRN360-K2-V," manufactured by Senju Metal

Industry Co., Ltd. for any internal tests of this product.

(2) Flux

Use rosin type flux in the soldering process.

If the flux below is used, some problems might be

caused in the product characteristics and reliability.

Please do not use these types of flux.

0.2wt%).

(*Water-soluble flux can be defined as non-rosin type

flux including wash-type flux and non-wash-type flux.)

Continued on the following page.

c Notice (Soldering and Mounting) PRF18/21 Series

R90E.pdf

Sep.24,2012

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical speciﬁcations. Therefore, please approve our product speciﬁcations or transact the approval sheet for product speciﬁcations before ordering.

PRF18BE471RB5RB Datasheet(PDF) 96 Page - Murata Manufacturing Co., Ltd.

PRF18BE471RB5RB Datasheet(HTML) 96 Page - Murata Manufacturing Co., Ltd.

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL