AD7265BCPZ datasheet(19/28 Pages) AD

19 / 28 page

AD7265

Rev. A | Page 19 of 28

MODES OF OPERATION

Once 32 SCLK cycles have elapsed, the D

The mode of operation of the AD7265 is selected by controlling

the (logic) state of the

OUT

line returns to

three-state on the 32

CS signal during a conversion. There are

three possible modes of operation: normal mode, partial power-

down mode, and full power-down mode. After a conversion is

initiated, the point at which

SCLK falling edge. If

is brought high

prior to this, the DOUT line returns to three-state at that point.

Therefore, CS may idle low after 32 SCLK cycles until it is

brought high again sometime prior to the next conversion

(effectively idling

CS is pulled high determines which

power-down mode, if any, the device enters. Similarly, if already

in a power-down mode,

CS low), if so desired, because the bus still

returns to three-state upon completion of the dual result read.

CS can control whether the device

returns to normal operation or remains in power-down. These

modes of operation are designed to provide flexible power

management options. These options can be chosen to optimize

the power dissipation/throughput rate ratio for differing

application requirements.

Once a data transfer is complete and D

A and D

OUT

B have

returned to three-state, another conversion can be initiated after

the quiet time, t

NORMAL MODE

This mode is intended for applications that need the fastest

throughput rates because the user does not have to worry about

any power-up times with the AD7265 remaining fully powered

at all times. Figure 34 shows the general diagram of the

operation of the AD7265 in this mode.

SCLK

LEADING ZEROS + CONVERSION RESULT

DOUTA

DOUTB

Figure 34. Normal Mode Operation

The conversion is initiated on the falling edge of CS, as

described in the Serial Interface section. To ensure that the part

remains fully powered up at all times, CS must remain low until

at least 10 SCLK falling edges have elapsed after the falling edge

of CS. If CS is brought high any time after the 10th SCLK falling

edge but before the 14th SCLK falling edge, the part remains

powered up, but the conversion is terminated and DOUTA and

DOUTB go back into three-state. Fourteen serial clock cycles are

required to complete the conversion and access the conversion

result. The DOUT line does not return to three-state after 14

SCLK cycles have elapsed, but instead does so when CS is

brought high again. If CS is left low for another 2 SCLK cycles

(for example, if only a 16 SCLK burst is available), two trailing

zeros are clocked out after the data. If CS is left low for a further

14 (or 16) SCLK cycles, the result from the other ADC on board

is also accessed on the same DOUT line, as shown in Figure 42

(see the Serial Interface section).

QUIET

, has elapsed by bringing

low again

(assuming the required acquisition time is allowed).

PARTIAL POWER-DOWN MODE

This mode is intended for use in applications where slower

throughput rates are required. Either the ADC is powered down

between each conversion, or a series of conversions may be

performed at a high throughput rate, and the ADC is then

powered down for a relatively long duration between these

bursts of several conversions. When the AD7265 is in partial

power-down, all analog circuitry is powered down except for

the on-chip reference and reference buffer.

To enter partial power-down mode, the conversion process

must be interrupted by bringing CS high anywhere after the

second falling edge of SCLK and before the 10th falling edge of

SCLK, as shown in

Figure 35. Once

is brought high in this

window of SCLKs, the part enters partial power-down, the

conversion that was initiated by the falling edge of CS is

terminated, and DOUTA and D

B go back into three-state. If

OUT

CS is brought high before the second SCLK falling edge, the

part remains in normal mode and does not power down. This

avoids accidental power-down due to glitches on the CS line.

SCLK

THREE-STATE

DOUTA

DOUTB

Figure 35. Entering Partial Power-Down Mode

AD7265BCPZ Datasheet(PDF) 19 Page - Analog Devices

AD7265BCPZ Datasheet(HTML) 19 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28

Datasheet Download

Link URL