AD9848AKST datasheet(20/32 Pages) AD

20 / 32 page

REV. A

AD9848/AD9849

–20–

H-Driver and RG Outputs

In addition to the programmable timing positions, the AD9848/

AD9849 features on-chip output drivers for the RG and H1–H4

outputs. These drivers are powerful enough to directly drive the

CCD inputs. The H-driver current can be adjusted for optimum

rise/fall time into a particular load by using the DRV registers.

The RG drive current is adjustable using the RGDRV register.

Each 3-bit DRV register is adjustable in 3.5 mA increments, with

the minimum setting of 0 equal to OFF or three-state, and the

maximum setting of 7 equal to 24.5 mA.

As shown in Figure 7, the H2/H4 outputs are inverses of H1/H3.

The internal propagation delay resulting from the signal inversion

is less than l ns, which is significantly less than the typical rise time

driving the CCD load. This results in a H1/H2 crossover voltage

at approximately 50% of the output swing. The crossover voltage

is not programmable.

Digital Data Outputs

The AD9848/AD9849 data output phase is programmable

using the DOUTPHASE register. Any edge from 0 to 47 may

be programmed, as shown in Figure 8.

HORIZONTAL CLAMPING AND BLANKING

The AD9848/AD9849’s horizontal clamping and blanking

pulses are fully programmable to suit a variety of applications.

As with the vertical timing generation, individual sequences are

defined for each signal and are then organized into multiple

regions during image readout. This allows the dark pixel clamping

and blanking patterns to be changed at each stage of the readout

to accommodate different image transfer timing and high speed

line shifts.

Table II. H1–H4, RG, SHP, SHD Timing Parameters

Length

Range

Description

POL

High/Low

Polarity Control for H1, H3, and RG (0 = No Inversion, 1 = Inversion)

POSLOC

0–47 Edge Location

Positive Edge Location for H1, H3, and RG

Sample Location for SHP, SHD

NEGLOC

0–47 Edge Location

Negative Edge Location for H1, H3, and RG

DRV

0–7 Current Steps

Drive Current for H1–H4 and RG Outputs (3.5 mA per Step)

Table III. Precision Timing Edge Locations

Quadrant

Edge Location (Decimal)

I0 to 11

0 to 11

000000 to 001011

12 to 23

16 to 27

010000 to 011011

III

24 to 35

32 to 43

100000 to 101011

36 to 47

48 to 59

110000 to 111011

FIXED CROSSOVER VOLTAGE

H1/H3

H2/H4

tPD

H2/H4

H1/H3

tRISE

tPD

tRISE

Figure 7. H-Clock Inverse Phase Relationship

NOTES

1. DIGITAL OUTPUT DATA (DOUT) PHASE IS ADJUSTABLE WITH RESPECT TO THE PIXEL PERIOD.

2. WITHIN 1 CLOCK PERIOD, THE DATA TRANSITION CAN BE PROGRAMMED TO ANY OF THE 48 LOCATIONS.

P[0]

P[48] = P[0]

CLI

1 PIXEL PERIOD

P[12]

P[24]

P[36]

DOUT

tOD

Figure 8. Digital Output Phase Adjustment

AD9848AKST Datasheet(PDF) 20 Page - Analog Devices

AD9848AKST Datasheet(HTML) 20 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32

Datasheet Download

Link URL