DSPIC33FJ12GP201TESLASHML datasheet(131/242 Pages) MICROCHIP

131 / 242 page

Preliminary

DS70264B-page 129

dsPIC33FJ12GP201/202

13.0 OUTPUT COMPARE

13.1

Setup for Single Output Pulse

Generation

When the OCM control bits (OCxCON<2:0>) are set to

‘100’, the selected output compare channel initializes

the OCx pin to the low state and generates a single

output pulse.

To generate a single output pulse, the following steps

are required. These steps assume timer source is

initially turned off but this is not a requirement for the

module operation.

1. Determine the instruction clock cycle time. Take

into account the frequency of the external clock to

the timer source (if one is used) and the timer

prescaler settings.

2. Calculate time to the rising edge of the output

pulse relative to the TMRy start value (0000h).

3. Calculate the time to the falling edge of the pulse

based on the desired pulse width and the time to

the rising edge of the pulse.

4. Write the value computed in step 2 into the Output

Compare register, OCxR, and the value computed

in step 3 into the Output Compare Secondary

5. Set Timer Period register, PRy, to a value equal to

or greater than value in OCxRS, the Output

Compare Secondary register.

6. Set the OCM bits to ‘100’ and the OCTSEL

(OCxCON<3>) bit to the desired timer source. The

OCx pin state will now be driven low.

7. Set the TON (TyCON<15>) bit to ‘1’, which

enables the compare time base to count. Upon the

first match between TMRy and OCxR, the OCx pin

will be driven high.

When the incrementing timer, TMRy, matches the

Output Compare Secondary register, OCxRS, the

second and trailing edge (high-to-low) of the pulse

is driven onto the OCx pin. No additional pulses

are driven onto the OCx pin and it remains at low.

As a result of the second compare match event,

the OCxIF interrupt flag bit is set. This will result in

an interrupt if it is enabled by setting the OCxIE bit.

For further information on peripheral interrupts,

refer to Section 6.0 “Interrupt Controller”.

8. To initiate another single pulse output, change the

Timer and Compare register settings, if needed,

and then issue a write to set the OCM bits to ‘100’.

Disabling and re-enabling the timer, and clearing

the TMRy register, are not required, but may be

advantageous for defining a pulse from a known

event time boundary.

The output compare module does not have to be

disabled after the falling edge of the output pulse.

Another pulse can be initiated by rewriting the value of

the OCxCON register.

13.2

Setup for Continuous Output

Pulse Generation

When the OCM control bits (OCxCON<2:0>) are set to

‘101’, the selected output compare channel initializes

the OCx pin to the low state and generates output

pulses on each and every compare match event.

To configure the module for generation of a continuous

stream of output pulses, the following steps are

required. These steps assume timer source is initially

turned off but this is not a requirement for the module

operation.

1. Determine the instruction clock cycle time. Take

into account the frequency of the external clock to

the timer source (if one is used) and the timer

prescaler settings.

2. Calculate time to the rising edge of the output

pulse relative to the TMRy start value (0000h).

3. Calculate the time to the falling edge of the pulse,

based on the desired pulse width and the time to

the rising edge of the pulse.

4. Write the values computed in step 2 into the Out-

put Compare register, OCxR, and value computed

in step 3 into the Output Compare Secondary

5. Set Timer Period register, PRy, to a value equal to

or greater than value in OCxRS, the Output

Compare Secondary Register.

6. Set the OCM bits to ‘101’ and the OCTSEL bit to

the desired timer source. The OCx pin state will

now be driven low.

7. Enable the compare time base by setting the TON

(TyCON<15>) bit to ‘1’. Upon the first match

between TMRy and OCxR, the OCx pin will be

driven high.

When the compare time base, TMRy, matches the

Output Compare Secondary register, OCxRS, the

second and trailing edge (high-to-low) of the pulse

is driven onto the OCx pin.

Note:

This data sheet summarizes the features

of the dsPIC33FJ12GP201/202 devices. It

is not intended to be a comprehensive

reference source. To complement the

information in this data sheet, refer to the

“dsPIC33F Family Reference Manual”.

Please see the Microchip web site

(www.microchip.com)

for

the

latest

dsPIC33F Family Reference Manual

sections.

DSPIC33FJ12GP201TE/ML Datasheet(PDF) 131 Page - Microchip Technology

DSPIC33FJ12GP201TE/ML Datasheet(HTML) 131 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL