DSPIC30F2011AT-30ESLASHPF datasheet(44/228 Pages) MICROCHIP

44 / 228 page

dsPIC30F6011/6012/6013/6014

DS70117F-page 42

4.2.3

MODULO ADDRESSING

APPLICABILITY

Modulo Addressing can be applied to the effective

address calculation associated with any W register. It is

important to realize that the address boundaries check

for addresses less than, or greater than the upper (for

incrementing buffers), and lower (for decrementing

buffers) boundary addresses (not just equal to).

Address changes may, therefore, jump beyond bound-

aries and still be adjusted correctly.

4.3

Bit-Reversed Addressing

Bit-Reversed Addressing is intended to simplify data

re-ordering for radix-2 FFT algorithms. It is supported

by the X AGU for data writes only.

The modifier, which may be a constant value or register

contents, is regarded as having its bit order reversed. The

address source and destination are kept in normal order.

Thus, the only operand requiring reversal is the modifier.

4.3.1

BIT-REVERSED ADDRESSING

IMPLEMENTATION

Bit-Reversed Addressing is enabled when:

BWM (W register selection) in the MODCON

cannot

accessed

using

Bit-Reversed

Addressing) and

the BREN bit is set in the XBREV register and

the Addressing mode used is Register Indirect

with Pre-Increment or Post-Increment.

If the length of a bit-reversed buffer is M = 2N bytes,

then the last ‘N’ bits of the data buffer start address

must be zeros.

XB<14:0> is the bit-reversed address modifier or ‘pivot

point’ which is typically a constant. In the case of an

FFT computation, its value is equal to half of the FFT

data buffer size.

When enabled, Bit-Reversed Addressing will only be

executed for register indirect with pre-increment or

post-increment addressing and word sized data writes.

It will not function for any other addressing mode or for

byte sized data, and normal addresses will be gener-

ated instead. When Bit-Reversed Addressing is active,

the W address pointer will always be added to the

address modifier (XB) and the offset associated with

the Register Indirect Addressing mode will be ignored.

In addition, as word sized data is a requirement, the

LSb of the EA is ignored (and always clear).

If Bit-Reversed Addressing has already been enabled

by setting the BREN (XBREV<15>) bit, then a write to

the XBREV register should not be immediately followed

by an indirect read operation using the W register that

has been designated as the bit-reversed pointer.

Note:

The modulo corrected effective address is

written back to the register only when Pre-

Modify or Post-Modify Addressing mode is

used to compute the effective address.

When an address offset (e.g., [W7 + W2])

is used, modulo address correction is per-

formed but the contents of the register

remain unchanged.

Note:

All bit-reversed EA calculations assume

word sized data (LSb of every EA is

always clear). The XB value is scaled

accordingly to generate compatible (byte)

addresses.

Note:

Modulo

Addressing

and

Bit-Reversed

Addressing

should

not

enabled

together. In the event that the user attempts

to do this, Bit-Reversed Addressing will

assume priority when active for the X

WAGU, and X WAGU Modulo Addressing

will

disabled.

However,

Modulo

Addressing will continue to function in the X

RAGU.

DSPIC30F2011AT-30E/PF Datasheet(PDF) 44 Page - Microchip Technology

DSPIC30F2011AT-30E/PF Datasheet(HTML) 44 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL