5429FCT520ATE datasheet(3/7 Pages) IDT

3 / 7 page

IDT29FCT520AT/BT/CT/DT, 521AT/BT/CT/DT

MULTILEVEL PIPELINE REGISTERS

MILITARY AND COMMERCIAL TEMPERATURE RANGES

6.2

CAPACITANCE (TA = +25

°C, f = 1.0MHz)

ABSOLUTE MAXIMUM RATINGS

(1)

Symbol

Rating

Commercial

Military

Unit

VTERM(2) Terminal Voltage

with Respect to

GND

–0.5 to +7.0

VTERM(3) Terminal Voltage

with Respect to

GND

–0.5 to

VCC +0.5

–0.5 to

VCC +0.5

Operating

Temperature

0 to +70

–55 to +125

°C

TBIAS

Temperature

Under Bias

–55 to +125

–65 to +135

°C

TSTG

Storage

Temperature

–55 to +125

–65 to +150

°C

Power Dissipation

0.5

IOUT

DC Output

Current

–60 to +120

NOTES:

1. Stresses greater than those listed under ABSOLUTE MAXIMUM RAT-

INGS may cause permanent damage to the device. This is a stress rating

only and functional operation of the device at these or any other conditions

above those indicated in the operational sections of this specification is

not implied.

Exposure to absolute maximum rating conditions for

extended periods may affect reliability. No terminal voltage may exceed

VCC by +0.5V unless otherwise noted.

2. Input and VCC terminals only.

3. Outputs and I/O terminals only.

DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE

Following Conditions Apply Unless Otherwise Specified:

Commercial: TA = 0

°C to +70°C, VCC = 5.0V ± 5%; Military: TA = –55°C to +125°C, VCC = 5.0V ± 10%

Symbol

Parameter

Test Conditions

(1)

Min.

Typ.

(2)

Max.

Unit

VIH

Input HIGH Level

Guaranteed Logic HIGH Level

2.0

—

VIL

Input LOW Level

Guaranteed Logic LOW Level

—

0.8

IIH

Input HIGH Current

(4)

VCC = Max.

VI = 2.7V

—

±1

µA

IIL

Input LOW Current

(4)

VCC = Max.

VI = 0.5V

—

±1

µA

IOZH

High Impedance

(4)

VCC = Max.

VO = 2.7V

—

±1

µA

IOZL

Output Current

VO = 0.5V

—

±1

Input HIGH Current

(4)

VCC = Max., VI = VCC (Max.)

—

±1

µA

VIK

Clamp Diode Voltage

VCC = Min., IN = –18mA

—

–0.7

–1.2

IOS

Short Circuit Current

VCC = Max.

(3), VO = GND

–60

–120

–225

VOH

Output HIGH Voltage

VCC = Min.

IOH = –6mA MIL.

2.4

3.3

—

VIN = VIH or VIL

IOH = –8mA COM’L.

IOH = –12mA MIL.

2.0

3.0

—

IOH = –15mA COM’L.

VOL

Output LOW Voltage

VCC = Min.

IOL = 32mA MIL.

—

0.3

0.5

VIN = VIH or VIL

IOL = 48mA COM’L.

Input Hysteresis

—

200

—

ICC

Quiescent Power

VCC = Max.

—

0.01

Supply Current

VIN = GND or VCC

NOTES:

2619 tbl 05

1. For conditions shown as Max. or Min., use appropriate value specified under Electrical Characteristics for the applicable device type.

2. Typical values are at VCC = 5.0V, +25

°C ambient.

3. Not more than one output should be shorted at one time. Duration of the short circuit test should not exceed one second.

4. The test limit for this parameter is

±5µA at TA = -55°C.

Symbol

Parameter(1)

Conditions

Typ.

Max. Unit

CIN

Input

Capacitance

VIN = 0V

COUT

Output

Capacitance

VOUT = 0V

2619 lnk 04

2619 lnk 03

NOTE:

1. This parameter is measured at characterization but not tested.

5429FCT520ATE Datasheet(PDF) 3 Page - Integrated Device Technology

5429FCT520ATE Datasheet(HTML) 3 Page - Integrated Device Technology

Html Pages

1 2 3 4 5 6 7

Datasheet Download

Link URL