HIP5020 datasheet(3/15 Pages) INTERSIL

3 / 15 page

2-15

Absolute Maximum Ratings

Thermal Information

Input Voltage, VIN . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +20.0V

Supply Voltage, VCC . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +20.0V

Shutdown Voltage . . . . . . . . . . . . . . . . . . . . . . . .-0.3V to VCC+0.3V

Voltage on PGND. . . . . . . . . . . . . . . . . . . . . . -2V to +2V (Transient)

All voltages are relative to GND, unless otherwise speciﬁed.

Operating Conditions

Voltage Range, VIN . . . . . . . . . . . . . . . . . . . . . . . . . +4.5V to +18.0V

Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0oC to 70oC

Oscillator Frequency Range. . . . . . . . . . . . . . . . . . 100kHz to 1MHz

Thermal Resistance (Typical, Note 1)

θJA (oC/W)

Plastic SOIC Package . . . . . . . . . . . . . . . . . . . . . . .

Plastic SOIC Package (with 1in2 copper). . . . . . . . .

Plastic SOIC Package (with 3in2 copper). . . . . . . . .

Maximum Junction Temperature (Plastic Package) . . . . . . . .125oC

Maximum Storage Temperature Range . . . . . . . . . . -65oC to 150oC

Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . .300oC

(SOIC - Lead Tips Only)

CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operationofthe

device at these or any other conditions above those indicated in the operational sections of this speciﬁcation is not implied.

NOTE:

θJA is measured with the component mounted on an evaluation PC board in free air.

Electrical Speciﬁcations

VIN = 6.3VDC, Components referenced from Figure 1. TYP values at TJ =25

oC and MIN, MAX limits are for T

from 0oC to 125oC; Unless Otherwise Speciﬁed

PARAMETER

SYMBOL

TEST CONDITIONS

TJ =

25oC0oC < TJ < 125

UNITS

TYP

MIN

MAX

REFERENCE

Reference Voltage

VFB

Total Variation, IO > IHMI

1.26

1.235

1.285

Temperature Stability

0.2

Hysteresis Width

∆

Hysteresis Mode; IO < IHMI

MODE CONTROL LOGIC

Under-Voltage Lockout Threshold

VCCUV

7.6

7.2

7.9

Under-Voltage Lockout Hysteresis

∆VCCUV

0.3

Shutdown Threshold

VSD

1.2

0.9

1.5

HMI Current Source

IHMI

µA

POWER MOSFETs

Drain Leakage Current

IDSS

VDSS = 20V, VPHASE = 0

0.35

µA

On State Resistance

rDS(ON)

VBOOT - VPHASE = 12.6V; IPHASE = 2A

125

Ω

Phase Rise and Fall Time

tr, tf

IO = 2ADC

CHARGE PUMP REGULATOR

VCC Regulation

VCC

VIN = 8.65V; FS = 100kHz;

C4 = C5 = 1.0

µF

14.8

14.0

16.0

Charge Pump Disable

VINCPN

9.8

VCC Current - Run Mode

ICC

FS = 100kHz

VINF Current - Hysteretic Mode

ICC - Idle

VFB = 5V, VCT = 0

110

µA

VCC Current - Shutdown

ICC

VSD = GND, VIN = 12V

µA

HIP5020

HIP5020 Datasheet(PDF) 3 Page - Intersil Corporation

HIP5020 Datasheet(HTML) 3 Page - Intersil Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

Datasheet Download

Link URL