LMC7215IMSLASHNOPB datasheet(3/19 Pages) TI

3 / 19 page

LMC7215, LMC7225

www.ti.com

SNOS882E – SEPTEMBER 1999 – REVISED MARCH 2013

2.7V to 5V Electrical Characteristics (continued)

Unless otherwise specified, all limits specified for TJ = 25°C, V

+ = 2.7V to 5V, V− = 0V, V

CM = VO = V

+/2. Boldface limits apply

at the temperature extremes.

Symbol

Parameter

Conditions

LMC7215

LMC7225

Units

Typ (1)

Limit(2)

Power Supply

PSRR

V+ = 2.2V to 8V

Rejection Ratio

min

Voltage Gain

140

V+ = 2.7V

3.0

2.9

CMRR > 50 dB

2.7

min

V+ = 2.7V

−0.2

0.0

CMRR > 50 dB

0.2

max

Input Common-Mode Voltage

CMVR

Range

V+ = 5.0V

5.3

5.2

CMRR > 50 dB

5.0

min

V+ = 5.0V

−0.3

−0.2

CMRR > 50 dB

0.0

max

V+ = 2.2V

2.05

1.8

IOH = 1.5 mA

1.7

min

V+ = 2.7V

2.05

2.3

VOH

Output Voltage High

IOH = 2.0 mA

2.2

min

V+ = 5.0V

4.8

4.6

IOH = 4.0 mA

4.5

min

V+ = 2.2V

0.17

0.4

IOH = 1.5 mA

0.5

max

V+ = 2.7V

0.17

0.4

VOL

Output Voltage Low

IOH = 2.0 mA

0.5

max

V+ = 5.0V

0.2

0.4

IOH = 4.0 mA

0.5

max

ISC+

Output Short Circuit Current

V+ = 2.7V, Sourcing

(4)

V+ = 5.0V, Sourcing

Output Short Circuit Current

V+ = 2.7V, Sinking

ISC−

(4)

V+ = 5.0V, Sinking

V+ = 2.2V

ILeakage

Output Leakage Current

VIN+ = 0.1V, VIN− = 0V,

0.01

500

max

VOUT = 15V

V+ = 5.0V

0.7

μA

Supply Current

VIN+ = 5V, VIN− = 0V

1.2

max

(4)

Do not short the output of the LMC7225 to voltages greater than 10V or damage may occur.

AC Electrical Characteristics

Unless otherwise specified, TJ = 25°C, V

+ = 5V, V− = 0V, V

CM = V

+/2

Symbol

Parameter

Conditions

LMC7215

LMC7225

Units

Typ(1)

Typ(1) (2)

trise

Rise Time

Overdrive = 10 mV (2)

12.2

μs

tfall

Fall Time

Overdrive = 10 mV (2)

0.4

0.35

μs

(1)

Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary

over time and will also depend on the application and configuration. The typical values are not tested and are not specified on shipped

production material.

(2)

All measurements made at 10 kHz. A 100 k

Ω pull-up resistor was used when measuring the LMC7225. CLOAD = 50 pF including the test

jig and scope probe. The rise times of the LMC7225 are a function of the R-C time constant.

Submit Documentation Feedback

Product Folder Links: LMC7215 LMC7225

LMC7215IM/NOPB Datasheet(PDF) 3 Page - Texas Instruments

LMC7215IM/NOPB Datasheet(HTML) 3 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19

Datasheet Download

Link URL