PIC16F628-04SLASHSS datasheet(135/160 Pages) MICROCHIP

135 / 160 page

Preliminary

DS40300B-page 135

PIC16F62X

17.2

DC CHARACTERISTICS:

PIC16LF62X-04 (Commercial, Industrial, Extended)

Standard Operating Conditions (unless otherwise stated)

Operating temperature

–40°C

≤ TA ≤ +85°C for industrial and

0°C

≤ TA ≤ +70°C for commercial and

–40°C

≤ TA ≤ +125°C for extended

Operating voltage VDD range as described in DC spec Table 17.1 and Table 12-2

Param

No.

Sym

Characteristic

Min

Typ† Max Units

Conditions

D001

VDD

Supply Voltage

2.0

5.5

D002

VDR

RAM Data Retention

Voltage (Note 1)

–

1.5*

–

Device in SLEEP mode

D003

VPOR

VDD start voltage to

ensure Power-on Reset

–VSS

–

See section on Power-on Reset for

details

D004

SVDD

VDD rise rate to ensure

Power-on Reset

0.05*

–

V/ms

See section on Power-on Reset for

details

D005

VBOD

Brown-out Detect Voltage

3.7

4.0

4.3

BODEN configuration bit is cleared

D010

D013

IDD

Supply Current (Note 2, 5)

–

4.0

–

0.6

7.0

6.0

2.0

FOSC = 4.0 MHZ, VDD = 2.5

FOSC = 20.0 MHz, VDD = 5.5

FOSC = 20.0 MHz, VDD = 4.5

FOSC = 10.0 MHz, VDD = 3.0

D020

IPD

Power Down Current (Note 2)

–

2.0

2.2

5.0

9.0

15.0

µA

VDD = 2.5

VDD = 3.0

VDD = 4.5

VDD = 5.5

VDD = 5.5 Extended

D023

∆IWDT

∆IBOD

∆ICOMP

∆IVREF

WDT Current (Note 4)

Brown-out Detect Current (Note 4)

Comparator Current for each

Comparator (Note 4)

VREF Current (Note 4)

–

6.0

125

135

µA

VDD=3.0V

BOD enabled, VDD = 5.0V

VDD = 3.0V

FOSC

LP Oscillator Operating Frequency

INTRC Oscillator Operating Frequency

XT Oscillator Operating Frequency

HS Oscillator Operating Frequency

–

200

KHz

MHz

All temperatures

These parameters are characterized but not tested.

†

Data in "Typ" column is at 5.0V, 25

°C, unless otherwise stated. These parameters are for design guidance only and are not

tested.

Note 1: This is the limit to which VDD can be lowered in SLEEP mode without losing RAM data.

2: The supply current is mainly a function of the operating voltage and frequency. Other factors such as I/O pin loading and

switching rate, oscillator type, internal code execution pattern, and temperature also have an impact on the current consump-

tion.

The test conditions for all IDD measurements in active operation mode are:

OSC1=external square wave, from rail to rail; all I/O pins tristated, pulled to VDD,

MCLR = VDD; WDT enabled/disabled as specified.

3: The power down current in SLEEP mode does not depend on the oscillator type. Power down current is measured with the

part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD to VSS.

4: The

∆ current is the additional current consumed when this peripheral is enabled. This current should be added to the base

IDD or IPD measurement.

5: For RC osc configuration, current through Rext is not included. The current through the resistor can be estimated by the for-

mula Ir = VDD/2Rext (mA) with Rext in k

Ω.

PIC16F628-04/SS Datasheet(PDF) 135 Page - Microchip Technology

PIC16F628-04/SS Datasheet(HTML) 135 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL