PIC16LC712-04SLASHP datasheet(65/108 Pages) MICROCHIP

65 / 108 page

Preliminary

DS41106A-page 65

PIC16C712/716

FIGURE 9-17: WAKE-UP FROM SLEEP THROUGH INTERRUPT

Q3 Q4

Q1 Q2

Q2 Q3 Q4

Q1 Q2 Q3 Q4

Q2 Q3

Q1 Q2

OSC1

CLKOUT(4)

INT pin

INTF flag

(INTCON<1>)

GIE bit

(INTCON<7>)

INSTRUCTION FLOW

Instruction

fetched

Instruction

executed

PC+1

PC+2

Inst(PC) = SLEEP

Inst(PC - 1)

Inst(PC + 1)

SLEEP

Processor in

SLEEP

Interrupt Latency

(Note 2)

Inst(PC + 2)

Inst(PC + 1)

Inst(0004h)

Inst(0005h)

Inst(0004h)

Dummy cycle

PC + 2

0004h

0005h

Dummy cycle

TOST(2)

PC+2

Note 1:

XT, HS or LP oscillator mode assumed.

TOST = 1024TOSC (drawing not to scale) This delay will not be there for RC osc mode.

GIE = ’1’ assumed. In this case after wake- up, the processor jumps to the interrupt routine. If GIE = ’0’, execution will continue in-line.

CLKOUT is not available in these osc modes, but shown here for timing reference.

9.14

Program Verification/Code Protection

If the code protection bit(s) have not been pro-

grammed, the on-chip program memory can be read

out for verification purposes.

9.15

ID Locations

Four memory locations (2000h - 2003h) are designated

as ID locations where the user can store checksum or

other code-identification numbers. These locations are

not accessible during normal execution, but are read-

able and writable during program/verify. It is recom-

mended that only the 4 least significant bits of the ID

location are used.

For ROM devices, these values are submitted along

with the ROM code.

Note:

Microchip does not recommend code pro-

tecting windowed devices.

9.16

In-Circuit Serial Programming™

PIC16CXXX microcontrollers can be serially pro-

grammed while in the end application circuit. This is

simply done with two lines for clock and data, and three

other lines for power, ground and the programming volt-

age. This allows customers to manufacture boards with

unprogrammed devices, and then program the micro-

controller just before shipping the product. This also

allows the most recent firmware or a custom firmware

to be programmed.

For complete details on serial programming, please

refer to the In-Circuit Serial Programming (ICSP™)

Guide, (DS30277).

PIC16LC712-04/P Datasheet(PDF) 65 Page - Microchip Technology

PIC16LC712-04/P Datasheet(HTML) 65 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL