ADC12L063EVAL datasheet(7/22 Pages) NSC

7 / 22 page

DC and Logic Electrical Characteristics (Continued)

Unless otherwise specified, the following specifications apply for AGND = DGND = DR GND = 0V, V

A =VD=VDR = +3.3V, PD

= 0V, V

REF = +1.0V, fCLK = 62 MHz, tr =tf = 2 ns, CL = 20 pF/pin. Boldface limits apply for TA =TJ =TMIN to TMAX: all

other limits T

A =TJ = 25˚C (Notes 7, 8, 9)

Symbol

Parameter

Conditions

Typical

(Note 10)

Limits

(Note 10)

Units

(Limits)

SFDR

Spurious Free Dynamic Range

IN = 1 MHz, Differential VIN =

−0.5 dBFS

IN = 10 MHz, Differential VIN =

−0.5 dBFS

dB(min)

IMD

Intermodulation Distortion

IN = 9.5 MHz and 10.5 MHz,

each = −7 dBFS

−75

dBFS

AC Electrical Characteristics

Unless otherwise specified, the following specifications apply for AGND = DGND = DR GND = 0V, V

A =VD,VDR = +3.3V, PD

= 0V, V

REF = +1.0V, fCLK = 62 MHz, tr =tf = 2 ns, CL = 20 pF/pin. Boldface limits apply for TA =TJ =TMIN to TMAX: all

other limits T

A =TJ = 25˚C (Notes 7, 8, 9, 12)

Symbol

Parameter

Conditions

Typical

(Note 10)

Limits

(Note 10)

Units

(Limits)

CLK1

Maximum Clock Frequency

MHz(min)

CLK2

Minimum Clock Frequency

MHz

Recommended Clock Duty Cycle

%(min)

%(max)

Clock High Time

6.5

ns(min)

Clock Low Time

6.5

ns(min)

CONV

Conversion Latency

Clock

Cycles

Data Output Delay after Rising

CLK Edge

DR = 2.5V

DR = 3.3V

ns(max)

Aperture Delay

Aperture Jitter

1.2

ps rms

DIS

Data outputs into TRI-STATE

Mode

Data Outputs Active after

TRI-STATE

Power Down Mode Exit Cycle

CLK

Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is

functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. The guaranteed

specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test

conditions.

Note 2: All voltages are measured with respect to GND = AGND = DGND = 0V, unless otherwise specified.

Note 3: When the input voltage at any pin exceeds the power supplies (that is, VIN < AGND, or VIN > VA,VD or VDR), the current at that pin should be limited to

25 mA. The 50 mA maximum package input current rating limits the number of pins that can safely exceed the power supplies with an input current of 25 mA to two.

Note 4: The absolute maximum junction temperature (TJmax) for this device is 150˚C. The maximum allowable power dissipation is dictated by TJmax, the

junction-to-ambient thermal resistance (

θJA), and the ambient temperature, (TA), and can be calculated using the formula PDMAX=(TJmax - TA )/θJA. In the 32-pin

LQFP,

θJA is 79˚C/W, so PDMAX = 1,582 mW at 25˚C and 823 mW at the maximum operating ambient temperature of 85˚C. Note that the power consumption of

this device under normal operation will typically be about 374 mW (354 typical power consumption + 20 mW TTL output loading). The values for maximum power

dissipation listed above will be reached only when the device is operated in a severe fault condition (e.g. when input or output pins are driven beyond the power

supply voltages, or the power supply polarity is reversed). Obviously, such conditions should always be avoided.

Note 5: Human body model is 100 pF capacitor discharged through a 1.5 k

Ω resistor. Machine model is 220 pF discharged through 0Ω.

Note 6: The 235˚C reflow temperature refers to infrared reflow. For Vapor Phase Reflow (VPR), the following Conditions apply: Maintain the temperature at the top

of the package body above 183˚C for a minimum 60 seconds. The temperature measured on the package body must not exceed 220˚C. Only one excursion above

183˚C is allowed per reflow cycle.

Note 7: The inputs are protected as shown below. Input voltages above VA or below GND will not damage this device, provided current is limited per (Note 3).

However, errors in the A/D conversion can occur if the input goes above VA or below GND by more than 100 mV. As an example, if VA is 3.3V, the full-scale input

voltage must be

≤3.4V to ensure accurate conversions.

ADC12L063EVAL Datasheet(PDF) 7 Page - National Semiconductor (TI)

ADC12L063EVAL Datasheet(HTML) 7 Page - National Semiconductor (TI)

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22

Datasheet Download

Link URL