ST7MC1 datasheet(303/308 Pages) STMICROELECTRONICS

303 / 308 page

ST7MC1/ST7MC2

303/308

15.7

MAXIMUM

VALUES

AVD

THRESHOLDS

On rev. A silicon versions, the max. values of AVD

thresholds are not tested in production.

15.8 EXTERNAL INTERRUPT MISSED

To avoid any risk if generating a parasitic interrupt,

the edge detector is automatically disabled for one

clock cycle during an access to either DDR and

OR. Any input signal edge during this period will

not be detected and will not generate an interrupt.

This case can typically occur if the application re-

freshes the port configuration registers at intervals

during runtime.

Workaround

The workaround is based on software checking

the level on the interrupt pin before and after writ-

ing to the PxOR or PxDDR registers. If there is a

level change (depending on the sensitivity pro-

grammed for this pin) the interrupt routine is in-

voked using the call instruction with three extra

PUSH instructions before executing the interrupt

routine (this is to make the call compatible with the

IRET instruction at the end of the interrupt service

routine).

But detection of the level change does not make

sure that edge occurs during the critical 1 cycle du-

ration and the interrupt has been missed. This may

lead to occurrence of same interrupt twice (one

hardware and another with software call).

To avoid this, a semaphore is set to '1' before

checking the level change. The semaphore is

changed to level '0' inside the interrupt routine.

When a level change is detected, the semaphore

status is checked and if it is '1' this means that the

last interrupt has been missed. In this case, the in-

terrupt routine is invoked with the call instruction.

There is another possible case i.e. if writing to

PxOR or PxDDR is done with global interrupts dis-

abled (interrupt mask bit set). In this case, the

semaphore is changed to '1' when the level

change is detected. Detecting a missed interrupt is

done after the global interrupts are enabled (inter-

rupt mask bit reset) and by checking the status of

the semaphore. If it is '1' this means that the last

interrupt was missed and the interrupt routine is in-

voked with the call instruction.

To implement the workaround, the following soft-

ware sequence is to be followed for writing into the

PxOR/PxDDR registers. The example is for for

Port PF1 with falling edge interrupt sensitivity. The

software sequence is given for both cases (global

interrupt disabled/enabled).

Case 1: Writing to PxOR or PxDDR with Global In-

terrupts Enabled:

LD A,#01

LD sema,A

; set the semaphore to '1'

LD A,PFDR

AND A,#02

LD X,A

; store the level before writing to

PxOR/PxDDR

LD A,#$90

LD PFDDR,A ; Write to PFDDR

LD A,#$ff

LD PFOR,A

; Write to PFOR

LD A,PFDR

AND A,#02

LD Y,A

; store the level after writing to

PxOR/PxDDR

LD A,X

; check for falling edge

cp A,#02

jrne OUT

TNZ Y

jrne OUT

LD A,sema

; check the semaphore status if

edge is detected

CP A,#01

jrne OUT

call call_routine; call the interrupt routine

OUT:LD A,#00

LD sema,A

.call_routine

; entry to call_routine

PUSH A

PUSH X

PUSH CC

.ext1_rt

; entry to interrupt routine

LD A,#00

LD sema,A

IRET

Case 2: Writing to PxOR or PxDDR with Global In-

terrupts Disabled:

SIM

; set the interrupt mask

LD A,PFDR

AND A,#$02

LD X,A

; store the level before writing to

PxOR/PxDDR

LD A,#$90

ST7MC1 Datasheet(PDF) 303 Page - STMicroelectronics

ST7MC1 Datasheet(HTML) 303 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL