FN6094 datasheet(3/11 Pages) INTERSIL

3 / 11 page

FN6094.3

November 5, 2004

Absolute Maximum Ratings

Thermal Information

V+ to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to 4.7V

Input Voltages

NO, NC, IN (Note 2) . . . . . . . . . . . . . . . . . . . -0.3 to ((V+) + 0.3V)

Output Voltages

COM (Note 2) . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to ((V+) + 0.3V)

Continuous Current NO, NC, or COM . . . . . . . . . . . . . . . . .

±300mA

Peak Current NO, NC, or COM

(Pulsed 1ms, 10% Duty Cycle, Max) . . . . . . . . . . . . . . . .

±500mA

ESD Rating:

HBM COMX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .>9kV

HBM NOX, NCX, INX, V+, GND . . . . . . . . . . . . . . . . . . . . . . .>4kV

MM COMX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .>500V

MM NOX, NCX, INX, V+, GND . . . . . . . . . . . . . . . . . . . . . . .>300V

CDM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .>1000V

Thermal Resistance (Typical, Note 3)

θJA (°C/W)

16 Ld 3x3 QFN Package . . . . . . . . . . . . . . . . . . . . .

16 Ld TSSOP Package . . . . . . . . . . . . . . . . . . . . . .

150

Maximum Junction Temperature (Plastic Package) . . . . . . . 150°C

Maximum Storage Temperature Range. . . . . . . . . . . . . -65°C to 150°C

Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300°C

(Lead Tips Only)

Operating Conditions

Temperature Range

ISL83699IX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40°C to 85°C

CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the

device at these or any other conditions above those indicated in the operational sections of this specification is not implied.

NOTES:

2. Signals on NC, NO, IN, or COM exceeding V+ or GND are clamped by internal diodes. Limit forward diode current to maximum current ratings.

θJA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details.

Electrical Specifications - 3V Supply

Test Conditions: V+ = +2.7V to +3.3V, GND = 0V, VINH = 1.4V, VINL = 0.5V (Notes 4, 6),

Unless Otherwise Specified

PARAMETER

TEST CONDITIONS

TEMP

(°C)

(NOTE 5)

MIN

TYP

(NOTE 5)

MAX

UNITS

ANALOG SWITCH CHARACTERISTICS

Analog Signal Range, VANALOG

Full

V+

ON Resistance, RON

V+ = 2.7V, ICOM = 100mA, VNO or VNC = 0V to V+,

(See Figure 5)

0.3

0.45

Ω

Full

0.6

Ω

RON Matching Between Channels,

∆RON

V+ = 2.7V, ICOM = 100mA, VNO or VNC = Voltage at

max RON, (Note 9)

0.04

0.08

Ω

Full

0.09

Ω

RON Flatness, RFLAT(ON)

V+ = 2.7V, ICOM = 100mA, VNO or VNC = 0V to V+,

(Note 7)

0.06

0.15

Ω

Full

0.15

Ω

NO or NC OFF Leakage Current,

INO(OFF) or INC(OFF)

V+ = 3.3V, VCOM = 0.3V, 3V, VNO or VNC = 3V, 0.3V

-3

Full

-20

COM ON Leakage Current,

ICOM(ON)

+ = 3.3V, VCOM = 0.3V, 3V, or VNO or VNC = 0.3V,

3V, or Floating

-4

Full

-45

DYNAMIC CHARACTERISTICS

Turn-ON Time, tON

V+ = 2.7V, VNO or VNC = 1.5V, RL = 50Ω, CL = 35pF,

(See Figure 1, Note 8)

Full

Turn-OFF Time, tOFF

V+ = 2.7V, VNO or VNC = 1.5V, RL = 50Ω, CL = 35pF,

(See Figure 1, Note 8)

Full

Break-Before-Make Time Delay, tD

V+ = 3.3V, VNO or VNC = 1.5V, RL = 50Ω, CL = 35pF,

(See Figure 3, Note 8)

Full

Charge Injection, Q

CL = 1.0nF, VG = 0V, RG = 0Ω, (See Figure 2)

-82

OFF Isolation

RL = 50Ω, CL = 5pF, f = 100kHz, VCOM = 1VRMS,

(See Figure 4)

Crosstalk (Channel-to-Channel)

RL = 50Ω, CL = 5pF, f = 100kHz, VCOM = 1VRMS,

(See Figure 6)

-98

Total Harmonic Distortion

f = 20Hz to 20kHz, VCOM = 2VP-P, RL = 600Ω

0.003

ISL83699

FN6094 Datasheet(PDF) 3 Page - Intersil Corporation

FN6094 Datasheet(HTML) 3 Page - Intersil Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11

Datasheet Download

Link URL