FN8796 Rev.2.00

Page 45 of 46

June 16, 2017

ISL68124

Intersil products are manufactured, assembled and tested utilizing ISO9001 quality systems as noted

in the quality certifications found at www.intersil.com/en/support/qualandreliability.html

Intersil products are sold by description only. Intersil may modify the circuit design and/or specifications of products at any time without notice, provided that such

modification does not, in Intersil's sole judgment, affect the form, fit or function of the product. Accordingly, the reader is cautioned to verify that datasheets are

current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its

subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or

otherwise under any patent or patent rights of Intersil or its subsidiaries.

For information regarding Intersil Corporation and its products, see www.intersil.com

For additional products, see www.intersil.com/en/products.html

© Copyright Intersil Americas LLC 2016-2017. All Rights Reserved.

All trademarks and registered trademarks are the property of their respective owners.

About Intersil

Intersil Corporation is a leading provider of innovative power management and precision analog solutions. The company's products

address some of the largest markets within the industrial and infrastructure, mobile computing, and high-end consumer markets.

For the most updated datasheet, application notes, related documentation, and related parts, please see the respective product

information page found at www.intersil.com.

For a listing of definitions and abbreviations of common terms used in our documents, visit: www.intersil.com/glossary.

You can report errors or suggestions for improving this datasheet by visiting www.intersil.com/ask.

Reliability reports are also available from our website at www.intersil.com/support.

warranted. Please go to web to make sure you have the latest revision.

DATE

REVISION

CHANGE

June 16, 2017

FN8796.2

Applied new header/footer.

Updated “Enable (EN0 and EN1) Input High Level” spec on page 9, removed typical and added a min spec of

2.55V.

Added “Enable (EN0 and EN1) Input Low Level” spec on page 9.

On page 10, changed from “SCL, SDA Input High/Low Threshold” to “SCL, SDA Input High Level” removed

typical and added Min spec of 1.55V.

Added “SCL, SDA Input Low Level” spec on page 10.

On pages 25 through 34, Updated the tables in the PMBus Command Detail section for the following

commands, changed from “Two’s Complement Integer” to “Unsigned Integer”.

-VOUT_COMMAND, VOUT_MAX, VOUT_MARGIN_HIGH, VOUT_MARGIN_LOW, VOUT_TRANSITION_RATE,

VOUT_DROOP,

VOUT_MIN, VOUT_OV_FAULT_LIMIT, VOUT_UV_FAULT_LIMIT, VIN_OV_FAULT_LIMIT,

VIN_UV_FAULT_LIMIT,

IIN_OC_FAULT_LIMIT, TON_DELAY, TON_RISE, TOFF_DELAY, and TOFF_FALL

Updated default value for ADh Command from “49D21300h” to “49D21E00h” in both the PMBus Command

Summary and PMBus Command Detail sections.

Updated “STATUS_CML (7Eh)” on page 39, changed Bit 1 meaning to “A communication fault other than the

ones listed in this table has occurred.”

Updated “READ_PIN (97h)” on page 42, changed Paged to Global.

January 27, 2017

FN8796.1

Pin descriptions on page 4:

Pin 31, RGND0 description changed “Positive” to “Negative”.

Pin 32, VSEN0 description changed “Negative” to “Positive”.

September 28, 2016

FN8796.0

Initial release