| Electronic Components Datasheet Search |
|
RSP1_Eval-Kit Datasheet(PDF) 5 Page - RFbeam Microwave GmbH |
|
|
|||||||||||||||||||||||||||||
RSP1_Eval-Kit Datasheet(HTML) 5 Page - RFbeam Microwave GmbH |
|
5 / 25 page ![]() RFbeam Microwave GmbH RSP1 Radar Processor Datasheet 5 Performance data 5.1 Overview RSP1 is working at an internal clock frequency of 32MHz. Radar I and Q signals pass a programmable gain amplifier (A=1 to 16). A 12Bit differential ADC running at a 500kHz clock converts the amplified signals. I and Q channels are acquired quasi parallel with a time shift of 2us. Complex 256pt fixpoint FFT runs in parallel to the data aqcuisition. Time signal passes a Hanning window and is then processed by the FFT. Acquisition is interrupted only by a 300us windowing calculation time. All other signal processing is performed in parallel to the data acquisition. 5.2 Internal Timing Sampling timing depends on setting of parameter S03 (sampling rate). This results in following FFT resolutions and measuring speed ranges: Parameter S03 (hex) fs (sampling freq.) df (resolution) max. speed remark 01 … 08 S03 value * 1280Hz 5Hz to 40Hz 4.5km/h to 116km/h allows direct readout of frequency 09 11.254kHz 44Hz (1km/h) 127km/h allows direct readout of speed in km/h 0A 22.528kHz 88Hz (2km/h) 255km/h allows direct readout of half speed Fig. 5: Acquiring and processing executes in parallel. A small gap (t3) occurs during windowing tacq = 256 * 1/fs = 11.4ms … 200ms (with fs = 22.5kHz … 1280kHz) t1 = 7.7ms FFT t2 = 2ms Logarithmic result conversion t3 = 0.3ms Hanning window calculation ADC Sampling of both channels is performed quasi-parallel with a maximum time shift of 2us max. 5.3 Response time Response time on parameter requests on sampling rate fs (parameter S03): tRmin = 11.4ms * A03 value (S03 = 0A) tRmax = 200ms * A03 value (S03 = 01) Update time on result parameters and digital outputs depend on sampling rate fs (parameter S03), on and immunity value (parameter A03) and on FFT avaraging (parameter S02). tUPDmin = 11.4ms * A03 value (S03 = 0A, S02 = 00) or 22.8ms * A03 value (S02 = 01) tUPDmax = 200ms * A03 value (S03 = 01, S02 = 00) or 400ms * A03 value (S02 = 01) See also chapter 8.4 Sampling Rate and Frequency Resolution © RFbeam Microwave GmbH www.rfbeam.ch December 11, 2015 5/25 1 1 2 2 3 3 1 2 3 Sampling Processing t1 t2 tacq t1 t3 |
|
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |