 |
Electronic Components Datasheet Search |
|
|
Electronic Components Datasheet Search |
|
HT95C40P Datasheet(PDF) 10 Page - Holtek Semiconductor Inc |
|
|
|||||||||||||||||||||||||||||
HT95C40P Datasheet(HTML) 10 Page - Holtek Semiconductor Inc |
|
|
10 / 51 page  HT95CXXX Rev. 1.50 10 May 26, 2005 Program Memory - ROM The program memory is used to store the program in- structions which are to be executed. It also contains data, table, and interrupt entries, and is organized into 8K ´16 bits´2 banks (HT95C400/40P) or 8K´16 bits (HT95C300/30P, HT95C200/20P) addressed by the program counter and table pointer. For the HT95C400/40P, the program memory is divided into 2 banks, each bank having a ROM Size 8K ´16 bits. To move from the present ROM bank to a different ROM bank, the higher 1 bits of the ROM address are set by the BP (Bank Pointer), while the remaining 13 bits of the PC are set in the usual way by executing the appropriate jump or call instruction. As the 14 address bits are latched during the execution of a call or jump instruction, the correct value of the BP must first be setup before a jump or call is executed. When either a software or hard- ware interrupt is received, note that no matter which ROM bank the program is in, the program will always jump to the appropriate interrupt service address in Bank 0. The original 14 bits address will be stored on the stack and restored when the relevant RET/RETI instruc- tion is executed, automatically returning the program to the original ROM bank. This eliminates the need for pro- grammers to manage the BP when interrupts occur. Certain locations in the program memory are reserved for special usage: · Location 0000H (Bank0) This area is reserved for the initialization program. Af- ter chip power-on reset or external reset or WDT time-out reset, the program always begins execution at location 0000H. · Location 0004H (Bank0) This area is reserved for the external interrupt service program. If the INT/TMR1 input pin is activated, the external interrupt is enabled and the stack is not full, the program begins execution at location 0004H. · Location 0008H (Bank0) This area is reserved for the Timer/Event Counter 0 in- terrupt service program. If a timer interrupt results from a Timer/Event Counter 0 overflow, the Timer/Event Counter 0 interrupt is enabled and the stack is not full, the program begins execution at loca- tion 0008H. · Location 000CH (Bank0) This location is reserved for the Timer/Event Counter 1 interrupt service program. If a timer interrupt results from a Timer/Event Counter 1 overflow, the Timer/Event Counter 1 interrupt is enabled and the stack is not full, the program begins execution at loca- tion 000CH. · Location 0010H (Bank0) This location is reserved for the peripherals interrupt service program. When the FSK decoder detects a ringer or line reversal or FSK carrier signal or FSK packet data, the FSK interrupt is generated. If these interrupts occurred, the peripheral interrupt is en- abled and the stack is not full, the program begins ex- ecution at location 0010H. The programmer could distinguish from these interrupts from the FSKS regis- ter. · Location 0014H (Bank0) This location is reserved for real time clock (RTC) in- terrupt service program. When RTC generator is en- abled and time-out occurs, the RTC interrupt is enabled and the stack is not full, the program begins execution at location 0014H. · Location 0018H (Bank0) This location is reserved for the HKS pin edge transi- tion or HDI pin falling edge transition or HFI pin rising edge transition. If this condition occurs, the dialer I/O interrupt is enabled and the stack is not full, the pro- gram begins execution at location 18H. 0 0 0 H 0 0 4 H 0 0 8 H D e v i c e i n i t i a l i z a t i o n p r o g r a m E x t e r n a l i n t e r r u p t s u b r o u t i n e T i m e r / e v e n t c o u n t e r 0 i n t e r r u p t s u b r o u t i n e P r o g r a m R O M 1 6 b i t s L o o k - u p t a b l e ( 2 5 6 w o r d s ) n 0 0 H L o o k - u p t a b l e ( 2 5 6 w o r d s ) n F F H T i m e r / e v e n t c o u n t e r 1 i n t e r r u p t s u b r o u t i n e 0 0 C H P e r i p h e r a l i n t e r r u p t s u b r o u t i n e 0 1 0 H R T C i n t e r r u p t s u b r o u t i n e 0 1 4 H D i a l e r I / O i n t e r r u p t s u b r o u t i n e 0 1 8 H N o t e : T h e L a s t p a g e f o r H T 9 5 C 4 0 0 / 4 0 P i s 3 F 0 0 H ~ 3 F F F H T h e L a s t p a g e f o r H T 9 5 C 3 0 0 / 3 0 P i s 1 F 0 0 H ~ 1 F F F H T h e L a s t p a g e f o r H T 9 5 C 2 0 0 / 2 0 P i s 1 F 0 0 H ~ 1 F F F H Program Memory |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
English ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
