AD5764CSU datasheet(22/27 Pages) AD

22 / 27 page

Preliminary Technical Data

AD5764

Rev. PrC 21-Oct-04| Page 23 of 28

AD5764 FEATURES

ANALOG OUTPUT CONTROL

In many industrial process control applications, it is vital that

the output voltage be controlled during power up and during

brownout conditions. When the supply voltages are changing,

the VOUT pin is clamped to 0 V via a low impedance path. To

prevent the output amp being shorted to 0 V during this time,

transmission gate G1 is also opened. These conditions are

maintained until the power supplies stabilize and a valid word is

written to the DAC register. At this time, G2 opens and G1

closes. Both transmission gates are also externally controllable

via the Reset In (RSTIN) control input. For instance, if RSTIN is

driven from a battery supervisor chip, the RSTIN input is

driven low to open G1 and close G2 on power-off or during a

brownout. Conversely, the on-chip voltage detector output

(RSTOUT) is also available to the user to control other parts of

the system. The basic transmission gate functionality is shown

in Figure 10.

VOLTAGE

MONITOR

AND

CONTROL

AGNDA

VOUTA

RSTOUT

RSTIN

Figure 10. Analog Output Control Circuitry

DIGITAL OFFSET AND GAIN CONTROL

The AD5764 incorporates a digital offset adjust function with a

±16 LSB adjust range and 0.125 LSB resolution. The gain

range. The full-scale output can be programmed to achieve full-

scale ranges of ±10 V, ±10.256 V, and ±10.526 V. A fine gain

trim is also available, allowing a trim range of ±16 LSB in 1 LSB

steps.

PROGRAMMABLE SHORT-CIRCUIT PROTECTION

The short-circuit current of the output amplifiers can be pro-

grammed by inserting an external resistor between the ISCC

pin and AGND. The programmable range for the current is

500 µA to 10 mA, corresponding to a resistor range of 120 kΩ

to 6 kΩ. If the ISCC pin is left unconnected the short circuit

current limit defaults to 5 mA. It should be noted that limiting

the short circuit current to a small value can affect the slew rate

of the output when driving into a capacitive load, therefore the

value of short-circuit current programmed should take into

account the size of the capacitive load being driven.

DIGITAL I/O PORT

The AD5764 contains a 2-bit digital I/O port (D1 and D0);

these bits can be configured as inputs or outputs independently,

and can be driven or have their values read back via the serial

interface. The I/O port signals are referenced to DVCC and

DGND. When configured as outputs, they can be used as con-

trol signals to multiplexers or can be used to control calibration

circuitry elsewhere in the system. When configured as inputs,

the logic signals from limit switches, for example, are applied to

D0 and D1 and can be read back via the digital interface.

TEMPERATURE SENSOR

The on-chip temperature sensor provides a voltage output that

is linearly proportional to the Centigrade temperature scale.

The typical accuracy of the temperature sensor is ±1°C at +25°C

and ±5°C over the −40°C to +105°C range. Its nominal output

voltage is 1.5V at +25°C, varying at 5 mV/°C, giving a typical

output range of 1.175V to 1.9 V over the full temperature range.

Its low output impedance, low self heating, and linear output

simplify interfacing to temperature control circuitry and A/D

converters.

LOCAL GROUND OFFSET ADJUST

The AD5764 incorporates a Local Ground Offset Adjust feature

which when enabled in the Function Register adjusts the DAC

outputs for voltage differences between The individual DAC

ground pins and the REFGND pin ensuring that the DAC

output voltages are always with respect to the local DAC ground

pin. For instance if pin AGNDA is at +5mV with respect to the

REFGND pin and VOUTA is measured with respect to

AGNDA then a +5mV error will result, enabling the Local

Ground Offset Adjust feature will offset VOUTA by +5mV

eliminating the error.

AD5764CSU Datasheet(PDF) 22 Page - Analog Devices

AD5764CSU Datasheet(HTML) 22 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27

Datasheet Download

Link URL