DSPIC30F datasheet(143/220 Pages) MICROCHIP

143 / 220 page

 2004 Microchip Technology Inc.

Preliminary

DS70116C-page 141

dsPIC30F5011/5013

20.3

Reset

The dsPIC30F differentiates between various kinds of

Reset:

Power-on Reset (POR)

MCLR Reset during normal operation

MCLR Reset during Sleep

Watchdog Timer (WDT) Reset (during normal

operation)

Programmable Brown-out Reset (BOR)

RESET

Instruction

Reset caused by trap lockup (TRAPR)

Reset caused by illegal opcode or by using an

uninitialized W register as an address pointer

(IOPUWR)

Different registers are affected in different ways by var-

ious Reset conditions. Most registers are not affected

by a WDT wake-up since this is viewed as the resump-

tion of normal operation. Status bits from the RCON

situations, as indicated in Table 20-5. These bits are

used in software to determine the nature of the Reset.

A block diagram of the On-Chip Reset Circuit is shown

in Figure 20-2.

A MCLR noise filter is provided in the MCLR Reset

path. The filter detects and ignores small pulses.

Internally generated Resets do not drive MCLR pin low.

FIGURE 20-2:

RESET SYSTEM BLOCK DIAGRAM

20.3.1

POR: POWER-ON RESET

A power-on event will generate an internal POR pulse

when a VDD rise is detected. The Reset pulse will occur

at the POR circuit threshold voltage (VPOR) which is

nominally 1.85V. The device supply voltage character-

istics must meet specified starting voltage and rise rate

requirements. The POR pulse will reset a POR timer

and place the device in the Reset state. The POR also

selects the device clock source identified by the oscil-

lator configuration fuses.

The POR circuit inserts a small delay, TPOR, which is

nominally 10

µs and ensures that the device bias cir-

cuits are stable. Furthermore, a user selected power-

up time-out (TPWRT) is applied. The TPWRT parameter

is based on device configuration bits and can be 0 ms

(no delay), 4 ms, 16 ms, or 64 ms. The total delay is at

device power-up, TPOR + TPWRT. When these delays

have expired, SYSRST will be negated on the next

leading edge of the Q1 clock and the PC will jump to the

Reset vector.

The timing for the SYSRST signal is shown in

Figure 20-3 through Figure 20-5.

MCLR

VDD

VDD Rise

Detect

POR

SYSRST

Sleep or Idle

Brown-out

Reset

BOREN

RESET

Instruction

WDT

Module

Digital

Glitch Filter

BOR

Trap Conflict

Illegal Opcode/

Uninitialized W Register

DSPIC30F Datasheet(PDF) 143 Page - Microchip Technology

DSPIC30F Datasheet(HTML) 143 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL