CS82C88 datasheet(5/11 Pages) INTERSIL

5 / 11 page

FN2979.2

August 25, 2005

Absolute Maximum Ratings

Thermal Information

Supply Voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +8.0V

Input, Output or I/O Voltage . . . . . . . . . . . . GND -0.5V to VCC +0.5V

ESD Classification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Class 1

Operating Conditions

Operating Voltage Range . . . . . . . . . . . . . . . . . . . . . +4.5V to +5.5V

Operating Temperature Range

C82C88 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to +70°C

I82C88 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-40°C to +85°C

M82C88 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-55°C to +125°C

Thermal Resistance (Typical)

JA (°C/W)

JC (°C/W)

CERDIP Package. . . . . . . . . . . . . . . .

CLCC Package . . . . . . . . . . . . . . . . .

PDIP Package . . . . . . . . . . . . . . . . . .

N/A

PLCC Package. . . . . . . . . . . . . . . . . .

N/A

Storage Temperature Range . . . . . . . . . . . . . . . . . . -65°C to +150°C

Maximum Junction Temperature

Ceramic Package. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +175°C

Plastic Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +150°C

Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . +300°C

(PLCC - Lead Tips Only)

Die Characteristics

Gate Count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100 Gates

CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the

device at these or any other conditions above those indicated in the operational sections of this specification is not implied.

DC Electrical Specifications VCC = 5.0V ± 10%;

TA = 0°C to +70°C (C82C88);

TA = -40°C to +85°C (I82C88);

TA = -55°C to +125°C (M82C88)

SYMBOL

PARAMETER

MIN

MAX

UNITS

TEST CONDITIONS

VIH

Logical One Input Voltage

2.0

2.2

C82C88, I82C88

M82C88

VIL

Logical Zero Input Voltage

0.8

VIHC

CLK Logical One Input Voltage

VCC -0.8

VILC

CLK Logical Zero Input Voltage

0.8

VOH

Output High Voltage

Command Outputs

3.0

VCC -0.4

-V

IOH = -8.0mA

IOH = -2.5mA

Output High Voltage

Control Outputs

3.0

VCC -0.4

-V

IOH = -4.0mA

IOH = -2.5mA

VOL

Output Low Voltage

Command Outputs

-0.5

IOL= +12.0mA

Output Low Voltage

Control Outputs

-0.4

IOL = +8.0mA

Input Leakage Current

-1.0

1.0

µAVIN = GND or VCC, except S0, S1, S2,

DIP Pins 1-2, 6, 15

IBHH

Input Leakage Current-Status Bus

-50

-300

µAVIN = 2.0V, S0, S1, S2 (See Note 1)

Output Leakage Current

-10.0

10.0

µAVO = GND or VCC, IOB = GND, AEN = VCC,

DIP Pins 7-9, 11-14

ICCSB

Standby Power Supply

µAVCC = 5.5V, VIN = VCC or GND, Outputs Open

ICCOP

Operating Power Supply Current

mA/MHz

VCC = 5.5V, Outputs Open (See Note 2)

NOTES:

1. IBHH should be measured after raising the VIN on S0, S1, S2 to VCC and then lowering to valid input high level of 2.0V.

2. ICCOP = 1mA/MHz of CLK cycle time (TCLCL)

Capacitance TA = +25°C

SYMBOL

PARAMETER

TYPICAL

UNITS

TEST CONDITIONS

CIN

Input Capacitance

FREQ = 1MHz, all measurements are

referenced to device GND

COUT

Output Capacitance

82C88

CS82C88 Datasheet(PDF) 5 Page - Intersil Corporation

CS82C88 Datasheet(HTML) 5 Page - Intersil Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11

Datasheet Download

Link URL