PCD5002USLASH10 datasheet(31/48 Pages) PHILIPS

31 / 48 page

1997 Jun 24

Philips Semiconductors

Product speciﬁcation

Advanced POCSAG and APOC-1 Paging

Decoder

PCD5002

Table 30 Identiﬁer bit allocation

Notes

1. The bit numbering corresponds with the numbering in a POCSAG codeword; bit 1 is the flag bit (0 = address,

1 = message).

2. A UPSW needs 18 bits to be matched for successful identification. Bit 1 (MSB) must be logic 0. Bits 2 to 19 contain

the identifier bit pattern, they are followed by 2 predetermined random (function) bits and the UPSW is completed by

10 CRC error correction bits and an even-parity bit.

3. Bits FR3 to FR1 (MSB: FR3) contain the 3 least significant bits of the 21-bit RIC.

4. Identifiers 1 and 2 (RIC only) will be disabled by programming bit D2 as logic 0.

Table 31 Identiﬁer types

BYTE

BIT (MSB: D7)

DESCRIPTION

D7 to D0

bits 2 to 9 of POCSAG codeword (RIC or UPSW); notes 1 and 2

D7 to D0

bits 10 to 17

D7 and D6

bits 18 and 19

frame number bit FR3 (RIC); note 3

frame number bit FR2 (RIC)

frame number bit FR1 (RIC)

identiﬁer type selection (0 = UPSW, 1 = RIC); note 4

identiﬁer enable (1 = enabled)

batch zero ID/continuous decoding (1 = enabled)

BYTE 3, BIT D2

BYTE 3, BIT D0

DESCRIPTION

user programmable sync word (UPSW)

continuous data decoding (CDD) sync word

normal user address (RIC)

batch zero identiﬁer

8.59

Voltage doubler

An on-chip voltage doubler provides an unregulated DC

output for supplying an LCD or a low power microcontroller

at output VPO. An external ceramic capacitor of 100 nF

(typ.) is required between pins CCN and CCP. The voltage

doubler is enabled via SPF programming.

8.60

Level-shifted interface

All interface lines are suited for communication with a

microcontroller operating from a higher supply voltage.

The external device must have a common reference at VSS

of the PCD5002.

The reference voltage for the level-shifted interface must

be applied to input VPR. If required this could be the

on-chip voltage doubler output VPO. When the

microcontroller has a separate (regulated) supply it should

be connected to VPR.

The level-shifted interface lines are RST, DON, ALC, REF

and INT.

The I2C-bus interface lines SDA and SCL can be

level-shifted independently of VPR by the standard external

pull-up resistors.

8.61

Signal test mode

A special ‘signal test’ mode is available for monitoring the

performance of a receiver circuit together with the

front-end of the PCD5002.

For this purpose the output of the digital noise filter and the

recovered bit clock are made available at outputs REF and

INT respectively. All synchronization and decoding

functions are normally active.

The ‘signal test’ mode is activated/deactivated by SPF

programming.

PCD5002U/10 Datasheet(PDF) 31 Page - NXP Semiconductors

PCD5002U/10 Datasheet(HTML) 31 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48

Datasheet Download

Link URL