SLRC61002HNT datasheet(29/139 Pages) NXP

29 / 139 page

NXP Semiconductors

SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

byte. In this case all the parameters (FIFO length, Watermark...) require a single byte only for definition. In case

of a 512 byte FIFO length the definition of this values requires 2 bytes.

8.5.2 Accessing the FIFO buffer

When the μ-Controller starts a command, the SLRC610 may, while the command is in progress, access the

FIFO-buffer according to that command. Physically only one FIFO-buffer is implemented, which can be used in

input and output direction. Therefore the μ-Controller has to take care, not to access the FIFO buffer in a way

that corrupts the FIFO data.

8.5.3 Controlling the FIFO buffer

Besides writing to and reading from the FIFO buffer, the FIFO-buffer pointers might be reset by setting the bit

FIFOFlush in FIFOControl to 1. Consequently, the FIFOLevel bits are set to logic 0, the actually stored bytes

are not accessible any more and the FIFO buffer can be filled with another 512 bytes (or 255 bytes if the bit

FIFOSize is set to 1) again.

8.5.4 Status Information about the FIFO buffer

The host may obtain the following data about the FIFO-buffers status:

• Number of bytes already stored in the FIFO-buffer. Writing increments, reading decrements the FIFO level:

FIFOLength in register FIFOLength (and FIFOControl Register in 512 byte mode)

• Warning, that the FIFO-buffer is almost full: HiAlert in register FIFOControl according to the value of the water

level in register WaterLevel (Register 02h bit [2], Register 03h bit[7:0])

• Warning, that the FIFO-buffer is almost empty: LoAlert in register FIFOControl according to the value of the

water level in register WaterLevel (Register 02h bit [2], Register 03h bit[7:0])

• FIFOOvl bit indicates, that bytes were written to the FIFO buffer although it was already full: ErrIRQ in register

IRQ0.

WaterLevel is one single value defining both HiAlert (counting from the FIFO top) and LoAlert (counting from the

FIFO bottom). The SLRC610 can generate an interrupt signal if:

• LoAlertIRQEn in register IRQ0En is set to logic 1 it will activate pin IRQ when LoAlert in the register

FIFOControl changes to 1.

• HiAlertIRQEN in register IRQ0En is set to logic 1 it will activate pin IRQ when HiAlert in the register

FIFOControl changes to 1.

The bit HiAlert is set to logic 1 if maximum water level bytes (as set in register WaterLevel) or less can be stored

in the FIFO-buffer. It is generated according to the following equation:

(2)

The bit LoAlert is set to logic 1 if water level bytes (as set in register WaterLevel) or less are actually stored in

the FIFO-buffer. It is generated according to the following equation:

(3)

SLRC610

All information provided in this document is subject to legal disclaimers.

Product data sheet

Rev. 5.1 — 3 January 2024

29 / 139

SLRC61002HNT Datasheet(PDF) 29 Page - NXP Semiconductors

SLRC61002HNT Datasheet(HTML) 29 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL