TC7126 datasheet(12/26 Pages) MICROCHIP

12 / 26 page

TC7126/A

DS21458C-page 12

6.0

COMPONENT VALUE

SELECTION

6.1

Auto-Zero Capacitor (CAZ)

The CAZ capacitor size has some influence on system

noise. A 0.47

μF capacitor is recommended for 200mV

full scale applications where 1LSB is 100

μV. A 0.033μF

capacitor is adequate for 2.0V full scale applications. A

mylar type dielectric capacitor is adequate.

6.2

Reference Voltage Capacitor (CREF)

The reference voltage, used to ramp the integrator out-

put voltage back to zero during the reference integrate

phase, is stored on CREF. A 0.1μF capacitor is accept-

able when VREF- is tied to analog common. If a large

Common mode voltage exists (VREF- – analog com-

mon) and the application requires a 200mV full scale,

increase CREF to 1μF. Rollover error will be held to less

than 0.5 count. A Mylar type dielectric capacitor is

adequate.

6.3

Integrating Capacitor (CINT)

CINT should be selected to maximize integrator output

voltage swing without causing output saturation. Due to

the TC7126A’s superior analog common temperature

coefficient specification, analog common will normally

supply the differential voltage reference. For this case,

a ±2V full scale integrator output swing is satisfactory.

For 3 readings per second (FOSC = 48kHz), a 0.047μF

value is suggested. For 1 reading per second, 0.15

μF

is recommended. If a different oscillator frequency is

used, CINT must be changed in inverse proportion to

maintain the nominal ±2V integrator swing.

An exact expression for CINT is:

EQUATION 6-1:

At 3 readings per second, a 750

Ω resistor should be

placed in series with CINT. This increases accuracy by

compensating for comparator delay. CINT must have

low dielectric absorption to minimize rollover error. A

polypropylene capacitor is recommended.

6.4

Integrating Resistor (RINT)

The input buffer amplifier and integrator are designed

with Class A output stages. The output stage idling

current is 6

μA. The integrator and buffer can supply

μA drive current with negligible linearity errors. RINT is

chosen to remain in the output stage linear drive

region, but not so large that PC board leakage currents

induce errors. For a 200mV full scale, RINT is 180kΩ. A

2V full scale requires 1.8M

Ω.

Note:

FOSC = 48kHz (3 readings per sec).

6.5

Oscillator Components

COSC should be 50pF; ROSC is selected from the

equation:

EQUATION 6-2:

For a 48kHz clock (3 conversions per second),

R = 180k

Ω.

Note that FOSC is 44 to generate the TC7126A’s

internal clock. The backplane drive signal is derived by

dividing FOSC by 800.

To achieve maximum rejection of 60Hz noise pickup,

the signal integrate period should be a multiple of

60Hz. Oscillator frequencies of 24kHz, 12kHz, 80kHz,

60kHz, 40kHz, etc. should be selected. For 50Hz rejec-

tion,

oscillator

frequencies

20kHz,

100kHz,

66-2/3kHz, 50kHz, 40kHz, etc. would be suitable. Note

that 40kHz (2.5 readings per second) will reject both

50Hz and 60Hz.

CINT =

(4000)

FOSC

VFS

RINT

⎛

⎝

⎛

⎝

⎞

⎠

⎞

⎠

VINT

Where:

FOSC = Clock frequency at Pin 38

VFS = Full scale input voltage

RINT = Integrating resistor

VINT = Desired full scale integrator output swing

Component

Value

Nominal Full Scale Voltage

200mV

CAZ

0.33

μF

0.033

μF

RINT

180k

1.8M

CINT

0.047

μF

0.047

μF

FOSC =

0.45

TC7126 Datasheet(PDF) 12 Page - Microchip Technology

TC7126 Datasheet(HTML) 12 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26

Datasheet Download

Link URL