THS7001, THS7002

70MHz PROGRAMMABLEGAIN AMPLIFIERS

SLOS214C − OCTOBER 1998 − REVISED MARCH 2007

6

POST OFFICE BOX 655303

PARAMETER

TEST CONDITIONS†

MIN

TYP

MAX

UNIT

SR

Slew rate (see Note 4)

G = −1

VO = ±2 V,

VCC = ±5 V

65

V/ s

SR

Slew rate (see Note 4)

G = −1

VO = ±10 V,

VCC = ±15 V

85

V/

µs

Settling time to 0.1%

VCC = ±5 V

85

ts

Settling time to 0.1%

G = −1,

VCC = ±15 V

70

ns

ts

Settling time to 0.01%

G = −1,

5 V Step

VCC = ±5 V

95

ns

Settling time to 0.01%

5 V Step

VCC = ±15 V

90

THD

Total harmonic distortion

VCC = ±15 V,

VO(PP) = 2V

fc = 1 MHz,

RL = 250 Ω

−88

dBc

Vn

Input noise voltage

VCC = ±5 V or ±15 V,

f = 10 kHz

1.7

nV/

√Hz

In

Input noise current

VCC = ±5 V or ±15 V,

f = 10 kHz

0.9

pA/

√Hz

BW

Small-signal bandwidth (−3 dB)

VO(PP) = 0.4V,

VCC = ±5 V

85

MHz

BW

Small-signal bandwidth (−3 dB)

VO(PP) = 0.4V,

G = 2

VCC = ±15 V

100

MHz

Bandwidth for 0.1 dB flatness

VO(PP) = 0.4V,

VCC = ±5 V

35

MHz

Bandwidth for 0.1 dB flatness

VO(PP) = 0.4V,

G = 2

VCC = ±15 V

45

MHz

Full power bandwidth (see Note 5)

VCC = ±5 V,

VO = 5 VO(PP)

4.1

MHz

Full power bandwidth (see Note 5)

VCC = ±15 V,

VO = 20 VO(PP)

1.4

MHz

AD

Differential gain error

G = 2, 100 IRE,

VCC = ±5 V

0.02%

AD

Differential gain error

G = 2, 100 IRE,

NTSC

VCC = ±15 V

0.02%

φD

Differential phase error

G = 2,

100 IRE,

VCC = ±5 V

0.01

°

φD

Differential phase error

G = 2,

100 IRE,

NTSC

VCC = ±15 V

0.01

°

VCC = ±5 V,

VO = ±2.5 V,

TA = 25°C

85

89

Open loop gain

CC

VO = ±2.5 V,

RL = 1 kΩ

TA = full range

83

dB

Open loop gain

VCC = ±15 V,

TA = 25°C

86

91

dB

VCC = ±15 V,

VO = ±10 V, RL = 1 kΩ

TA = full range

84

Channel-to-channel crosstalk (THS7002)

VCC = ±5 V or ±15 V,

f = 1 MHz

−85

dB

† Full range for the THS7001/02C is 0°C to 70°C. Full range for the THS7001/02I is −40°C to 85°C.

NOTES:

4. Slew rate is measured from an output level range of 25% to 75%.

5. Full power bandwidth = slew rate/2

π V(PP).

shutdown electrical characteristics

PARAMETER

TEST CONDITIONS

MIN

TYP

MAX

UNIT

Standby current, disabled

Preamp

VCC = ±5 V

0.2

0.3

ICC(standby)

Standby current, disabled

(per channel)

Preamp

VI(SHDN) = 2.5 V

VCC = ±15 V

0.65

0.8

mA

ICC(standby)

(per channel)

PGA

VI(SHDN) = 2.5 V

VCC = ±5 V or ±15 V

0.8

1.2

mA

VIH(SHDN)

Shutdown voltage for power up

VCC = ±5 V or ±15 V,

Relative to GND

0.8

V

VIL(SHDN)

Shutdown voltage for power down

VCC = ±5 V or ±15 V,

Relative to GND

2

V

IIH(SHDN)

Shutdown input current high

VCC = ±5 V or ±15 V,

VI(SHDN) = 5 V

300

400

µA

IIL(SHDN)

Shutdown input current low

VCC = ±5 V or ±15 V,

VI(SHDN) = 0.5 V

25

50

µA

tdis

Disable time†

VCC = ±5 V or ±15 V,

Preamp and PGA

100

ns

ten

Enable time†

VCC = ±5 V or ±15 V,

Preamp and PGA

1.5

µs

† Disable time and enable time are defined as the interval between application of the logic signal to SHDN and the point at which the supply current

has reached half its final value.