| Electronic Components Datasheet Search |
|
MCP9902 Datasheet(PDF) 25 Page - Microchip Technology |
|
|
|||||||||||||||||||||||||||||
MCP9902 Datasheet(HTML) 25 Page - Microchip Technology |
|
25 / 50 page ![]() 2015-2016 Microchip Technology Inc. DS20005382C-page 25 MCP9902/3/4 REGISTER 5-6: CONFIG: CONFIGURATION REGISTER (ADDRESSES 03H AND 09H) RW-0 RW-0 RW-0 RW-0 RW-0 RW-0 RW-0 RW-0 MSKAL R/S AT/THM RECD1 RECD2 RANGE DA_DIS APDD bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as 0 -n = Value at POR ‘1’ = bit is set ‘0’ = Bit is cleared x = Bit in unknown 7 MSKAL : Masks the ALERT/THERM2 pin from asserting when the ALERT/THERM2 pin is in interrupt mode. This bit has no effect when the ALERT/THERM2 pin is in comparator mode. 1 = The ALERT/THERM2 pin is masked and will not be asserted for any interrupt condition when the ALERT/THERM2 pin is in interrupt mode. The Status Register will be updated normally. 0 = The ALERT/THERM2 pin is not masked. If any of the appropriate status bits are set, the ALERT/THERM2 pin will be asserted. 6 R/S : Controls Active/Standby states 1 = The device is in Standby state and not converting (unless a one-shot has been commanded) 0 = The device is in Active state and converting on all channels 5 AT/THM : Controls the operation of the ALERT/THERM2 pin 1 = The ALERT/THERM2 pin acts in comparator mode as described in Section 4.6.2 “ALERT/THERM2 Pin In THERM Mode” . In this mode the MASK_ALL bit is ignored. 0 = The ALERT/THERM2 pin acts in interrupt mode as described in Section 4.6.1 “ALERT/THERM2 Pin Interrupt Mode” . 4 RECD1 : Disables the Resistance Error Correction (REC) for the External Diode 1 1 = REC is disabled for the External Diode 1 0 = REC is enabled for the External Diode 1 3 RECD2 : Disables the Resistance Error Correction (REC) for External Diode 2 and External Diode 3 1 = REC is disabled for External Diode 2 and External Diode 3 0 = REC is enabled for External Diode 2 and External Diode 3 2 RANGE : Configures the measurement range and data format of the temperature channels 1 = The temperature measurement range is -64°C to +191.875°C and the data format is offset binary (see Table 4-7) 0 = The temperature measurement range is 0°C to +127.875°C and the data format is binary 1 DA_DIS : Disables the dynamic averaging feature on all temperature channels 1 = The dynamic averaging feature is disabled 0 = The dynamic averaging feature is enabled. All temperature channels will be converted with an averaging factor that is based on the conversion rate as shown in Table 4-1. 0 APDD (MCP9904 only): Disables the anti-parallel diode operation 1 = Anti-parallel diode mode is disabled. Only one external diode will be measured on the DP2 and DN2 pins. 0 = Anti-parallel diode mode is enabled. Two external diodes will be measured on the DP2 and DN2 pins. |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |