| Electronic Components Datasheet Search |
|
L99MM70XP Datasheet(PDF) 55 Page - STMicroelectronics |
|
|
|||||||||||||||||||||||||||||
L99MM70XP Datasheet(HTML) 55 Page - STMicroelectronics |
|
55 / 68 page ![]() L99MM70XP SPI control and status registers Doc ID 022637 Rev 2 55/68 Table 34. Control registers 2 Control register 2 (02h) Bit 15 14 13 12 11 10 9 8 7 65 432 1 0 Reset state 0 0 0 0 0 0 0 0 0 00 000 0 0 Name reserved ECFDLS ECVLS OUT9 OUT8HS2 OUT8HS1 OUT7 OUT6 ECND EC5 EC4 EC3 EC2 EC1 EC0 ECON Table 35. Control registers 2, bits Bit name Comment reserved Reserved bit, has always to be written to 0 and reads always 0 ECFDLS 1: switch on the ECFD LS driver 0: switch off the ECFD LS driver ECVLS 1: switch on the ECV LS driver 0: switch off the ECV LS driver If the ECVPWM1 bit (CR4/Bit4) is also set, then the ECV output is controlled by the PWM1 input OUT9 1: switch on the OUT9 HS driver 0: switch off the OUT9 HS driver If the OUT9PWM1 bit (CR4/Bit11) is also set, then the OUT9 output is controlled by the PWM1 input OUT8HS2 11: switch off the OUT8 HS driver 10: switch on the OUT8 HS driver (high current mode) 01: switch on the OUT8 HS driver (low current mode) 00: switch off the OUT8 HS driver If the OUT8PWM3 bit (CR4/Bit10) is also set, then the OUT8 output is controlled by the PWM3 input OUT8HS1 OUT7 1: switch on the OUT7 HS driver 0: switch off the OUT7 HS driver If the OUT7PWM1 bit (CR4/Bit9) is also set, then the OUT7 output is controlled by the PWM1 input This bit is disabled if ECON = 1. In this case OUT7 is switched on permanently. OUT6 1: switch on the OUT6 HS driver 0: switch off the OUT6 HS driver If the OUT6PWM2 bit (CR4/Bit8) is also set, then the OUT6 output is controlled by the PWM2 input ECND EC negative discharge: 0: EC negative discharge off 1: EC negative discharge on EC5 Reference value for difference voltage amplifier at pin ECV, binary coded. The full scale value is set in ECVL (CR3/Bit5). If all EC bits are set to zero, the reference value is 0V. EC4 EC3 EC2 EC1 EC0 ECON 1: EC control enabled 0: EC control disabled If the EC control is enabled, the output OUT7 is switched on permanently. |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |