ISL6207

FN9075 Rev 8.00

Page 5 of 10

December 2, 2005

Functional Pin Description

UGATE (Pin 1 for SOIC-8, Pin 8 for QFN)

The UGATE pin is the upper gate drive output. Connect to

the gate of high-side power N-Channel MOSFET.

BOOT (Pin 2 for SOIC-8, Pin 1 for QFN)

BOOT is the floating bootstrap supply pin for the upper gate

drive. Connect the bootstrap capacitor between this pin and

the PHASE pin. The bootstrap capacitor provides the charge

to turn on the upper MOSFET. See the Bootstrap Diode and

Capacitor section under DESCRIPTION for guidance in

choosing the appropriate capacitor value.

PWM (Pin 3 for SOIC-8, Pin 2 for QFN)

The PWM signal is the control input for the driver. The PWM

signal can enter three distinct states during operation, see the

three-state PWM Input section under DESCRIPTION for further

details. Connect this pin to the PWM output of the controller. In

addition, place a 500k

 resistor to ground from this pin. This

allows for proper three-state operation under all start-up

conditions.

GND (Pin 4 for SOIC-8, Pin 3 for QFN)

GND is the ground pin. All signals are referenced to this node.

LGATE (Pin 5 for SOIC-8, Pin 4 for QFN)

LGATE is the lower gate drive output. Connect to gate of the

low-side power N-Channel MOSFET.

VCC (Pin 6 for SOIC-8, Pin 5 for QFN)

Connect the VCC pin to a +5V bias supply. Place a high

quality bypass capacitor from this pin to GND.

EN (Pin 7 for SOIC-8, Pin 6 for QFN)

EN is the enable input pin. Connect this pin to HIGH to

enable, and LOW to disable, the IC. When disabled, the IC

draws less than 1

A bias current.

PHASE (Pin 8 for SOIC-8, Pin 7 for QFN)

Connect the PHASE pin to the source of the upper MOSFET

and the drain of the lower MOSFET. This pin provides a

return path for the upper gate driver.

Description

Operation

Designed for speed, the ISL6207 dual MOSFET driver

controls both high-side and low-side N-Channel FETs from

one externally provided PWM signal.

A rising edge on PWM initiates the turn-off of the lower

MOSFET (see Timing Diagram). After a short propagation

section. Adaptive shoot-through circuitry monitors the LGATE

voltage and determines the upper gate delay time

below 1V. This prevents both the lower and upper MOSFETs

from conducting simultaneously, or shoot-through. Once this

delay period is completed, the upper gate drive begins to rise

UGATE Turn-On Propagation Delay

10

20

30

ns

LGATE Turn-On Propagation Delay

10

20

30

ns

OUTPUT

Upper Drive Source Resistance

500mA Source Current

-

1.0

2.5



-10°C to 85°C

-

1.0

2.2



Upper Driver Source Current (Note 5)

-

2.0

-

A

Upper Drive Sink Resistance

500mA Sink Current

-

1.0

2.5



-10°C to 85°C

-

1.0

2.2



Upper Driver Sink Current (Note 5)

-

2.0

-

A

Lower Drive Source Resistance

500mA Source Current

-

1.0

2.5



-10°C to 85°C

-

1.0

2.2



Lower Driver Source Current (Note 5)

-

2.0

-

A

Lower Drive Sink Resistance

500mA Sink Current

-

0.4

1.0



-10°C to 85°C

-

0.4

0.8



Lower Driver Sink Current (Note 5)

-

4.0

-

A

NOTE:

5. Guaranteed by characterization, not 100% tested in production.

Electrical Specifications

Recommended Operating Conditions, Unless Otherwise Noted. (Continued)

PARAMETER

SYMBOL

TEST CONDITIONS

MIN

TYP

MAX

UNITS