 |
Electronic Components Datasheet Search |
|
|
Electronic Components Datasheet Search |
|
PCD5041HZ Datasheet(PDF) 5 Page - NXP Semiconductors |
|
|
|||||||||||||||||||||||||||||
PCD5041HZ Datasheet(HTML) 5 Page - NXP Semiconductors |
|
|
5 / 28 page  1996 Oct 31 5 Philips Semiconductors Objective specification DECT burst mode controller PCD5041 INT 24 27 O interrupt (active LOW) CLK100 25 29 O 100 Hz frame timer VSS3 26 31 P negative supply 3 DO 27 32 O 3-state data output on the speech interface FS3 − 33 I/O 8 kHz framing signal to ADPCM CODEC 1 output, for simple base + handset, otherwise 8 kHz framing input FS1 28 34 I/O 8 kHz framing signal to ADPCM CODEC 1 output, for simple base + handset, otherwise 8 kHz framing input FS4 − 35 I/O 8 kHz framing signal to ADPCM CODEC 1 output, for simple base + handset, otherwise 8 kHz framing input FS2 29 36 O 8 kHz framing signal to ADPCM CODEC 2 in the base station mode DI 30 37 I data input on the speech interface DCK 31 38 O simple base + handset; 1152 kHz data clock (output), otherwise 2048 kHz data clock (input) signal CLK3 32 39 O 3.456 MHz clock (nominal value, used to adjust system timing) ANT_SW 33 40 O selects one of two antennas T_ENABLE 34 41 O Transmitter Enable (active LOW) T_POWER_RMP 35 43 O Transmitter Power Ramp control RMT_STAT 36 44 I serial 8-bit data can be read in for each slot; REMote radio SYNTH_LOCK 37 45 I lock indication from synthesizer VSS4 38 46 P negative supply 4 REF_CLK 39 47 O reference frequency for the synthesizer, i.e. the crystal oscillator clock fCLK VDD2 40 48 P positive supply 2 S_ENABLE 41 49 O synthesizer enable S_CLK 42 51 O clock signal, to be used with S_DATA S_DATA 43 52 O serial data to the synthesizer S_POWER_DWN 44 53 O synthesizer power-down control VCO_BND_SW 45 54 O VCO bandswitch control signal 1200 HZ 46 55 O control signal for dual synthesizer schemes T_DATA 47 56 O serial output data to transmitter SET_OFF_IN 48 57 I switches off the crystal oscillator, and prevents all RF signals from becoming active TEST1 49 58 I selects various test modes.; normal operation set to 0 RSSI_AN 50 60 I analog signal (for basic DECT systems), peak signal strength measured after a lowpass filter TEST2 51 − I selects various test modes; normal operation set to 0 TEST3 52 61 I selects various test modes; normal operation set to 0 R_DATA 53 63 I receive data SYMBOL PIN TYPE(2) DESCRIPTION QFP64 LQFP80(1) |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
English ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
