Specifications are subject to change without notice WM30 96 DS 240914

5

WM30 96

RS485 (on request)

Type

Multidrop, bidirectional

(static and dynamic

variables)

Connections

2-wire

Max. distance 1000m,

termination directly on the

module

Addresses

247, selectable by means

of the front key-pad

Protocol

MODBUS/JBUS (RTU)

Data (bidirectional)

Dynamic (reading only)

System and phase

variables: see table “List of

variables...”

Static (reading and writing only) All the configuration

parameters.

Data format

1 start bit, 8 data bit,

no/even/odd parity,1 stop bit

Baud-rate

Selectable: 9.6k, 19.2k,

38.4k, 115.2k bit/s

Driver input capability

1/5 unit load. Maximum

160 transceivers on the

same bus.

Note

With the rotary switch (on

the back of the basic unit)

in lock position the

modification of the

programming parameters

and the reset command by

means of the serial

communication is not

allowed anymore. In this

case just the data reading

is allowed.

Insulation

See “Insulation between

inputs and outputs” table

RS232 port (on request)

Type

Bidirectional (static and

dynamic variables)

Connections

3 wires. Max. distance

15m

Protocol

MODBUS RTU /JBUS

Data (bidirectional)

Dynamic (reading only)

System and phase

variables: see table “List of

variables...”

Static (reading and writing only) All the configuration

parameters

Data format

1 start bit, 8 data bit,

no/even/odd parity,1 stop

bit

Baud-rate

Selectable: 9.6k, 19.2k,

38.4k, 115.2k bit/s

Note

With the rotary switch (on

the back of the basic unit)

in lock position the

modification of the

programming parameters

and the reset command by

means of the serial

communication is not

allowed anymore. In this

case just the data reading

is allowed.

Insulation

See “Insulation between

inputs and outputs” table

Ethernet/Internet port

(on request)

Protocols

Modbus TCP/IP

IP configuration

Static IP / Netmask /

Default gateway

Port

Selectable (default 502)

Client connections

Max 5 simultaneously

Connections

RJ45 10/100 BaseTX

Max. distance 100m

Data (bidirectional)

Dynamic (reading only)

System and phase

variables: see table “List of

variables...”

Static (reading and

writing only)

All the configuration

parameters.

Note

With the rotary switch (on

the back of the basic unit)

in lock position the

modification of the

programming parameters

and the reset command by

means of the serial

communication is not

allowed anymore. In this

case just the data reading

is allowed.

Insulation

See “Insulation between

inputs and outputs” table

BACnet-IP

(on request)

Protocols

BACnet-IP (for

measurement reading

purpose and to write

object description) and

Modbus TCP/IP (for

measurement reading

purpose and for

programming parameter

purpose)

BACnet-IP

IP configuration

Static IP / Netmask

/Default gateway

Port

Fixed: BAC0h

Device object instance

0 to 9999 selectable by

key-pad 0 to 2^22-2 =

4.194.302, selectable by

programming software or

by BACnet.

Supported services

“I have”, “I am”, “Who

has”, “Who is”, “Read

(multiple) Property”

Supported objects

Type 2 (analogue value,

including COV property),

Type 5 (binary-value for up

to 16 virtual alarm re-

transmission) Type 8

(device)

IP configuration

Static IP / Netmask /

Default gateway

Modbus TCP/IP

See “Ethernet/Internet

port” above

Client connections

Modbus only: max 5

simultaneously

Connections

RJ45 10/100 BaseTX Max.

distance 100m

Output specifications (cont.)