Specifications are subject to change without notice WM30 96 DS 240914

9

WM30 96

Standard compliance

Safety

IEC60664, IEC61010-1

EN60664, EN61010-1

EN62052-11.

Metrology

EN62053-22, EN62053-23,

EN50470-3.

Pulse output

DIN43864, IEC62053-31

Approvals

Eligible System

performance Meter for Go

Solar California, CE, cULus

“Listed”

Connections

Screw-type

Cable cross-section area

max. 2.5 mm2.

min./max. screws

tightening torque: 0.4 Nm /

0.8 Nm.

Suggested screws

tightening torque: 0.5 Nm

Housing DIN

Dimensions (WxHxD)

Module holder:

96x96x50mm.

“A” and “B” type modules:

89.5x63x16mm.

“C” type module:

89.5x63x20mm.

Max. depth behind the panel

With 3 modules (A+B+C):

81.7 mm

Material

ABS/Nylon PA66, self-

extinguishing: UL 94 V-0

Mounting

Panel mounting

Protection degree

Front

IP65, NEMA4x, NEMA12

Screw terminals

IP20

Weight

Approx. 420 g (packing

included)

Operating temperature

-25°C to +55°C (-13°F to

131°F) (R.H. from 0 to 90%

non-condensing @ 40°C)

according to EN62053-21,

EN50470-1 and EN62053-

23

Storage temperature

-30°C to +70°C (-22°F to

158°F) (R.H. < 90% non-

condensing @ 40°C)

according to EN62053-21,

EN50470-1 and EN62053-

23

Installation category

Cat. III (IEC60664,

EN60664)

Insulation (for 1 minute)

See “Insulation between

inputs and outputs” table

Dielectric strength

4kVAC RMS for 1 minute

Noise rejection CMRR

100 dB, 48 to 62 Hz

EMC

According to EN62052-11

Electrostatic discharges

15kV air discharge

Immunity to irradiated

Test with current: 10V/m

from 80 to 2000MHz

Electromagnetic fields

Test without any current:

30V/m from 80 to 2000MHz

Burst

On current and voltage

measuring inputs circuit:

4kV

Immunity to conducted

disturbances

10V/m from 150KHz to

80MHz

Surge

On current and voltage

measuring inputs circuit:

4kV; on “L” auxiliary power

supply input: 1kV

Radio frequency suppression

According to CISPR 22

General specifications

Insulation between inputs and outputs

(1): respect another module 4kV, in the same module 0kV.

-: combination not allowed.

NOTE: all the models have, mandatory, to be connected to external current transformers because the isolation among the

current inputs is just functional (100VAC).

PowerSupply

(HoL)

Mesuring

inputs

Relèoutput

(MOR2)

Staticouput

(MOO2)

Serialport Ethernetport Analogue

outputs

PowerSupply

(HoL)

-

4kV

4kV

4kV

4kV

4kV

4kV

Mesuringinputs

4kV

-

4kV

4kV

4kV

4kV

4kV

Relèoutput

(MOR2)

4kV

4kV

2kV

-

4kV

4kV

4kV

Staticouput

(MOO2)

4kV

4kV

-

2kV

4kV

4kV

4kV

Serialport

4kV

4kV

4kV

4kV

-

-

4kV

Ethernetport

4kV

4kV

4kV

4kV

-

-

4kV

Analogueoutputs

4kV

4kV

4kV

4kV

4kV

4kV

4kV(1)